Yamaha 2005 YZF-R1T Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 106

background image

OPERATION AND IMPORTANT RIDING POINTS

5-2

5

serve the battery. Do not crank the en-
gine more than 10 seconds on any one
attempt.

CAUTION:

ECA11130

For maximum engine life, always
warm the engine up before starting
off. Never accelerate hard when the
engine is cold!

NOTE:

The engine is warm when it quickly re-
sponds to the throttle.

EAU16671

Shifting

Shifting gears lets you control the
amount of engine power available for
starting off, accelerating, climbing hills,
etc.
The gear positions are shown in the il-
lustration.

NOTE:

To shift the transmission into the neu-
tral position, press the shift pedal down
repeatedly until it reaches the end of its
travel, and then slightly raise it.

CAUTION:

ECA10260

●

Even with the transmission in
the neutral position, do not
coast for long periods of time
with the engine off, and do not
tow the motorcycle for long dis-
tances. The transmission is
properly lubricated only when
the engine is running. Inade-
quate lubrication may damage
the transmission.

●

Always use the clutch while
changing gears to avoid damag-
ing the engine, transmission,
and drive train, which are not
designed to withstand the
shock of forced shifting.

1. Shift pedal

2. Neutral position

U5VY21E0.book Page 2 Friday, September 10, 2004 9:21 AM

«
...
45
46
47
48
49
...
»

Содержание 2005 YZF-R1T











































































































Отзывы:

Нет отзывов

Похожие инструкции для 2005 YZF-R1T

Бренд: KEEWAY Страницы: 164

Бренд: R&G Страницы: 4

Бренд: Dennis Kirk Страницы: 5

Бренд: X-lite Страницы: 84

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 144

Бренд: Yamaha Страницы: 84

Бренд: Yamaha Страницы: 255

Бренд: Yamaha Страницы: 17

Бренд: Suzuki Страницы: 101

Бренд: R&G Страницы: 9

Бренд: BMW Страницы: 19

Бренд: hepco & becker Страницы: 2

Бренд: Shark Страницы: 80

Бренд: Yamaha Страницы: 80

Бренд: Yamaha Страницы: 278

Бренд: KYMCO Страницы: 68

Бренд: KYMCO Страницы: 229

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды