Yamaha 115 Скачать руководство пользователя страница 75 | Manualshive

Страница: 75 / 90

background image

69

Trouble Recovery

EMU29427

Troubleshooting

A problem in the fuel, compression, or igni-
tion systems can cause poor starting, loss of
power, or other problems. This section de-
scribes basic checks and possible remedies,
and covers all Yamaha outboard motors.
Therefore some items may not apply to your
model.
If your outboard motor requires repair, bring
it to your Yamaha dealer.
If the engine trouble-alert indicator is flash-
ing, consult your Yamaha dealer.

Starter will not operate.

Q. Is battery capacity weak or low?
A. Check battery condition. Use battery of
recommended capacity.

Q. Are battery connections loose or corrod-
ed?
A. Tighten battery cables and clean battery
terminals.

Q. Is fuse for electric start relay or electric cir-
cuit blown?
A. Check for cause of electric overload and
repair. Replace fuse with one of correct am-
perage.

Q. Are starter components faulty?
A. Have serviced by a Yamaha dealer.

Q. Is shift lever in gear?
A. Shift to neutral.

Engine will not start (starter operates).

Q. Is fuel tank empty?
A. Fill tank with clean, fresh fuel.

Q. Is fuel contaminated or stale?

A. Fill tank with clean, fresh fuel.

Q. Is fuel filter clogged?
A. Clean or replace filter.

Q. Is starting procedure incorrect?
A. See page 43.

Q. Has fuel pump malfunctioned?
A. Have serviced by a Yamaha dealer.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

Q. Are spark plug cap(s) fitted incorrectly?
A. Check and re-fit cap(s).

Q. Is ignition wiring damaged or poorly con-
nected?
A. Check wires for wear or breaks. Tighten
all loose connections. Replace worn or bro-
ken wires.

Q. Are ignition parts faulty?
A. Have serviced by a Yamaha dealer.

Q. Is engine shut-off cord (lanyard) not at-
tached?
A. Attach cord.

Q. Are engine inner parts damaged?
A. Have serviced by a Yamaha dealer.

Engine idles irregularly or stalls.

Q. Are spark plug(s) fouled or of incorrect
type?
A. Inspect spark plug(s). Clean or replace
with recommended type.

«
...
73
74
75
76
77
...
»

Содержание 115



























































































Отзывы:

Нет отзывов

Похожие инструкции для 115

ADRF5515A-EVALZ

Бренд: Analog Devices Страницы: 9

B450M MORTAR TITANIUM

Бренд: MSI Страницы: 144

Бренд: Advantech Страницы: 4

Бренд: NXP Semiconductors Страницы: 32

Бренд: IBASE Technology Страницы: 72

Бренд: Ublox Страницы: 25

Бренд: OpenVox Страницы: 29

BrillianX 1S/2000

Бренд: QDI Страницы: 63

Бренд: Analog Devices Страницы: 6

Бренд: Micrel Страницы: 10

Бренд: Gigabyte Страницы: 104

Бренд: Sleipner Страницы: 24

Z77A-GD65 GAMING series

Бренд: MSI Страницы: 98

Бренд: Watersnake Страницы: 24

Бренд: MATSONIC Страницы: 52

Бренд: HiSilicon Страницы: 10

Бренд: CHAINTECH Страницы: 48

Бренд: CHAINTECH Страницы: 33

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды