Yamaha 115 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 90

background image

Operation

40

EMU27234

Filling fuel and engine oil

EMU30321

Filling fuel for models without a fuel
joint

WARNING

EWM01830

●

Gasoline and its vapors are highly flam-
mable and explosive. Always refuel ac-
cording to this procedure to reduce the
risk of fire and explosion.

●

Gasoline is poisonous and can cause
injury or death. Handle gasoline with
care. Never siphon gasoline by mouth.
If you should swallow some gasoline or
inhale a lot of gasoline vapor, or get
some gasoline in your eyes, see your
doctor immediately. If gasoline spills
on your skin, wash with soap and wa-
ter. If gasoline spills on your clothing,

change your clothes.

1.

Stop the engine.

2.

Be sure you are in a well-ventilated out-
door area, either securely moored or
trailered.

3.

Make sure no one is in the boat.

4.

Do not smoke and keep away from
sparks, flames, static electric discharge,
or other sources of ignition.

5.

If you use a portable container to store
and dispense fuel, only use a locally ap-
proved GASOLINE container.

6.

Touch the fuel nozzle to the filler open-
ing or funnel to help prevent electrostatic
sparks.

7.

Fill the fuel tank, but do not overfill. Fuel
can expand and overflow if the tempera-
ture increases.

8.

Tighten the filler cap securely.

9.

Wipe up any spilled gasoline immediate-
ly with dry rags. Dispose rags properly.

According to local laws or regulations.

EMU27282

Filling oil

This engine uses the Yamaha oil injection
system, which provides superior lubrication
by ensuring the proper oil ratio for all operat-
ing conditions. No fuel premixing is needed.
Simply pour gasoline into the fuel tank and
oil into the oil tank. Convenient indicator seg-
ments indicate the status of the oil supply.
For details on reading the indicator seg-
ments, see page 42.

WARNING

EWM00530

Do not add gasoline into the oil tank. Fire

or explosion could result.

To fill the engine oil tank, proceed as follows:
1.

Pour engine oil into the remote oil tank.

TIP:

The oil level lines on the remote oil tank indi-
cate the amount of additional oil that can be
added to the tank. The top oil level line indi-
cates approximately 1.9 L (0.5 US gal, 0.4
Imp gal) can be added, and the bottom oil
level line indicates approximately 3.8 L (1 US
gal, 0.8 Imp gal) can be added.
2.

Turn on the main switch. The Yamaha

Engine oil tank capacity:

0.9 L (0.95 US qt, 0.79 Imp.qt)

ZMU04142

«
...
44
45
46
47
48
...
»

Содержание 115



























































































Отзывы:

Нет отзывов

Похожие инструкции для 115

Бренд: Hailo Страницы: 22

Бренд: Intel Страницы: 6

Бренд: Abit Страницы: 104

Бренд: AOpen Страницы: 156

Бренд: Elitegroup Computer Systems Страницы: 82

Бренд: Supero Страницы: 105

RHINO VAP133-ACP

Бренд: Octek Страницы: 66

Бренд: Aeroflex Страницы: 20

Бренд: National Semiconductor Страницы: 22

Бренд: ASROCK Страницы: 83

790XT-G35 series

Бренд: MSI Страницы: 103

Бренд: Gigabyte Страницы: 96

Бренд: Aaeon Страницы: 119

Бренд: PC Partner Страницы: 20

Бренд: JETWAY Страницы: 45

Бренд: Supero Страницы: 89

Бренд: Engbo Страницы: 64

SpacePC 1232 Series

Бренд: Parvus Страницы: 87

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды