Yamaha 115 Скачать руководство пользователя страница 49 | Manualshive

Страница: 49 / 90

background image

Operation

43

EMU27451

Operating engine

EMU27482

Feeding fuel

WARNING

EWM00420

●

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the
water near you.

●

When the air vent screw is loosened,
gasoline vapor will be released. Gaso-
line is highly flammable, and its vapors
are flammable and explosive. Refrain
from smoking, and keep away from
open flames and sparks while loosen-
ing the air vent screw.

●

This product emits exhaust gases
which contain carbon monoxide, a col-
orless, odorless gas which could cause
brain damage or death when inhaled.
Symptoms include nausea, dizziness,
and drowsiness. Keep cockpit and cab-
in areas well ventilated. Avoid blocking

exhaust outlets.

1.

If there is an air vent screw on the fuel
tank cap, loosen it 2 or 3 turns.

2.

If there is a fuel joint or a fuel cock on the
boat, firmly connect the fuel line to the
joint or open the fuel cock.

3.

Squeeze the primer pump, with the ar-
row pointing up, until you feel it become
firm.

EMU27492

Starting engine

WARNING

EWM01600

Before starting the engine, make sure
that the boat is tightly moored and that
you can steer clear of any obstructions.
Be sure there are no swimmers in the wa-

ter near you.

EMU27645

Electric start / remote control models

WARNING

EWM01840

●

Failure to attached engine shut-off cord
could result in a runaway boat if opera-
tor is ejected. Attach the engine shut-
off cord to a secure place on your cloth-
ing, or your arm or leg while operating.
Do not attach the cord to clothing that
could tear loose. Do not route the cord
where it could become entangled, pre-
venting it from functioning.

●

Avoid accidentally pulling the cord dur-
ing normal operation. Loss of engine
power means the loss of most steering
control. Also, without engine power,
the boat could slow rapidly. This could
cause people and objects in the boat to

be thrown forward.

1.

Place the remote control lever in neutral.

ZMU02025

«
...
47
48
49
50
51
...
»

Содержание 115



























































































Отзывы:

Нет отзывов

Похожие инструкции для 115

Бренд: J&W Страницы: 28

Бренд: Linear Technology Страницы: 16

970 Extreme3 R2.0

Бренд: ASROCK Страницы: 70

Бренд: Texas Instruments Страницы: 25

Бренд: Zida Страницы: 28

Бренд: Procomp Страницы: 55

Бренд: DFI Страницы: 62

Бренд: Biostar Страницы: 65

Бренд: Magic-Pro Computer Страницы: 40

Бренд: DFI Страницы: 115

Бренд: OLIMEX Страницы: 17

Бренд: DG Страницы: 18

Бренд: MSI Страницы: 87

Бренд: IEI Technology Страницы: 11

Бренд: J&W Страницы: 42

Бренд: MSI Страницы: 6

Бренд: MSI Страницы: 48

Бренд: ASROCK Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды