Press
Press
Press
Press each keypad key for response when pressed.
Apply 9V battery to terminals below the keypad for
Programming Instructions
Press
Enter Master PIN code
Press
Enter 4-8 digit PIN code
"Unlock"
Audio Mode
All Code Lockout Mode
Enable
Enable
Disable
Disable
For quiet areas, select Disable (3)
in Audio Mode.
Programming Troubleshooting
Symptom
Suggested Action
Press
Press
Press
Press
Press
Definitions
Changing Master PIN Code
1
Enter 4-8
digit Master
PIN Code.
Creating User PIN Codes
2
Master PIN code must be created first.
*Max User Codes = 250 in network
Unlocking Door with PIN Code
3
Enter PIN
Press
Resetting Lock to Factory Default
Factory Settings
Settings
Factory Setting
Master PIN Code
Registration
required*
Automatic Re-lock
Disabled
One Touch Locking
Enabled
Audio
Enabled
Automatic Re-lock Time
30 Seconds
Wrong Code Entry Limit
5 Times
Shutdown Time
60 Seconds
*The Master PIN code must be registered prior to any other programming of the lock.
When lock is reset to factory defaults all
user codes (including the Master PIN
code*) are deleted and all programming
features are reset to original default
settings (see "Factory Default Settings").
2. Remove the batteries.
1. Remove the battery cover.
Upon reset, Master Code creation is the
only option available and must be
performed prior to any other
programming of the lock.
4. Replace battery cover.
NOTE: After setting the Master Code,
press any key to complete handing of
the lock.
3. While pressing the reset button
(minimum of 3 seconds) reinstall
batteries. Release reset button.
Default settings
in
bold.
Enrolling Lock In Z-Wave Plus Network
Your network controller first needs to be in
enrollment or exclusion mode for the lock
to be enrolled or removed from network.
1. Remove the battery cover.
2. Press button and hold until unit beeps
two (2) times.
Once you put the controller in the
enrollment or exclusion mode, the lock
can be enrolled or removed in the Z-Wave
Plus Plus network by pressing the
button.
3. Release button and network removal
automatically begins.
To enroll lock using the button option:
3. Release button and network joining
automatically begins.
4. Replace battery cover.
1. Remove the battery cover.
4. Replace battery cover.
To remove lock using the button option:
2. Press button and hold until unit beeps
five (5) times.
Product Support Tel 1-855-213-5841 • www.yalehome.com
ASSA ABLOY Residential Group. Other products' brand names may be trademarks or registered
permission of ASSA ABLOY Residential Group is prohibited.
Yale® and Yale Real Living® are registered trademarks of
© Copyright 2019. All rights reserved. Reproduction in whole or in part without the express written
trademarks of their respective owners and are mentioned for reference purposes only.
Master PIN Code must be created before any further programming.
Max User Codes = 250 in network
Warning:
Changes or modifications to this device, not expressly approved by
ASSA ABLOY Residential Group could void the user's authority to operate the
equipment.
PIN Code Management - Up to 250 Users (in network)
Duplicate if necessary
User Name
PIN Code
Code Chart
Low Battery Warning
Flashes RED
All Code Lockout Mode:
This feature is enabled by the Master code. When enabled, it
restricts all user (except Master) PIN code access. When attempting to enter a code while
the unit is in Lockout, the lock rapidly beeps 5 times.
Audio Mode:
Choosing
Disable (3)
in Audio mode shuts off the code confirmation tone
play-back for use in quiet areas. Audio mode is enabled or disabled through feature
programming by the Master code.
Automatic Re-lock Time:
After a successful code entry or manual unlock with the key, the
lock will automatically re-lock after each unlock in an effort to keep your home secure. This
feature is optional, and can be turned off. In the ON mode, the lock will automatically re-lock
after thirty (30) seconds.
Low Battery:
When battery power is low, the Low Battery Warning Indicator flashes RED. If
battery power is completely lost, use the 9Volt battery override. To use the 9V battery
override apply 9V battery, in either direction, to terminals below the keypad for backup
power option. Wake up the lock and enter your pin code to unlock the door.
Master PIN Code:
The Master PIN code is used for programming and for feature settings.
It
must be created prior to programming the lock.
The Master code will also operate
(unlock/lock) the lock.
Network Setting:
This setting is available through the wireless button on the interior
escutcheon and allows the lock to connect with a network controller.
User PIN Code:
The User code operates the lock. Maximum number of user codes is 250 in
network.
Wrong Code Entry Limit:
After five (5) unsuccessful attempts at entering a valid PIN code,
the unit will shut down and not allow operation for sixty (60) seconds.
Tamper Alert:
Audible alarm sounds if attempting to forcibly remove outside lock from door.
One Touch Locking:
When the latch is retracted, activating the keypad will extend the latch
(during Automatic Re-lock duration or when Automatic Re-lock is disabled).
Shutdown Time:
The unit will shutdown (flashing keypad) for sixty (60) seconds and not
allow operation after the wrong code entry limit has been met.
All Code Lockout Mode
Rapidly beeps 5 times
Failsafe 9 Volt
Battery Connection
(Use Alkaline battery)
®
While Yale has included several features to prevent lockout (9-
Volt battery jumper, low battery warnings), it is still possible for
a lockout situation to occur. Because this product does not
®
have a mechanical override (a key), Yale recommends to use
this product in an environment where there are additional
entry points into the dwelling.
NOTE TO INSTALLER AND CONSUMER
Keypad Wake-Up
M
U
Master PIN Code Setting
User PIN Code Registration
Register
Delete
Complete
Handing the Lock
Preforms automatic
handing of the lock
Advanced Lock Settings
Automatic Re-lock
Disable
30 sec
One Touch Locking
Enable
Disable
Continue
60 sec
3 min
2 min
U
2. Enter the 4-8 digit Master PIN code followed by the
key.
3. Enter digit corresponding to the function to be performed followed by the
key.
1. Wake the lock by pressing the .
!
Warning:
Changes or modifications to this device, not expressly approved by
ASSA
ABLOY Residential Group
could void the user's authority to operate the equipment.
Industry Canada:
Section 7.1.3 of RSS-GEN
This Device complies with
Industry Canada License-exempt RSS standard(s).
Operation is subject to the following two conditions: 1)
this device may not cause interference, and 2) this
device must accept any interference, including
interference that may cause undesired operation of the
device.
Contain 11626A- YRIZW2USTS1
Le présent émetteur radio 6982A-YRHCPZW0FM a été
approuvé par Industrie Canada pour fonctionner avec
les types d'antenne énumérés ci-dessous et ayant un
gain admissible maximal. Les types d'antenne non
inclus dans cette liste, et dont le gain est supérieur au
gain maximal indiqué, sont strictement interdits pour
l'exploitation de l'émetteur.
CAN ICES-3B/NMB-3B
Section 7.1.2 of RSS-GEN
Under Industry Canada
regulations, this radio transmitter may only operate
using an antenna of a type and maximum (or lesser)
gain approved for the transmitter by Industry Canada.
To reduce potential radio interference to other users,
the antenna type and its gain should be so chosen that
the equivalent isotropically radiated power (e.i.r.p.) is
not more than that necessary for successful
communication.
En vertu des règlements d'Industrie Canada, cet
émetteur radio ne peut fonctionner avec une antenne
d'un type et un maximum (ou moins) approuvés pour
gagner de l'émetteur par Industrie Canada. Pour
réduire le risque d'interférence aux autres utilisateurs,
le type d'antenne et son gain doivent être choisies de
façon que la puissance isotrope rayonnée équivalente
(PIRE) ne dépasse pas ce qui est nécessaire pour une
communication réussie.
Model: YRD156-ZW-619,605,0BP
This radio transmitter 6982A-YRHCPZW0FM has been
approved by Industry Canada to operate with the
antenna types listed below with the maximum
permissible gain indicated. Antenna types not included
in this list, having a gain greater than the maximum
gain indicated for that type, are strictly prohibited for
use with this device.
Cet appareil est conforme avec Industrie Canada RSS
standard exemptes de licence(s). Son fonctionnement
est soumis aux deux conditions suivantes: 1) ce
dispositif ne peut causer des interférences, et 2) cet
appareil doit accepter toute interférence, y compris les
interférences qui peuvent causer un mauvais
fonctionnement du dispositif.
Ÿ
Connect the equipment into an outlet on a circuit
different from that to which the receiver is
connected.
THIS DEVICE COMPLIES WITH PART 15 OF THE FCC
RULES. OPERATION IS SUBJECT TO THE FOLLOWING
TWO CONDITIONS.
This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful
interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful Interference to radio or television reception,
which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
FCC:
Contain FCC ID: 2ABFG- YRIZW2USTS1
Ÿ
Reorient or relocate the receiving antenna.
Model: YRD156-ZW-619,605,0BP
Ÿ
Increase the separation between the equipment
and receiver.
Ÿ
Consult the dealer or an experienced radio/TV
technician for help.
(1) THIS DEVICE MAY NOT CAUSE HARMFUL
INTERFERENCE, AND (2) THIS DEVICE MUST ACCEPT
ANY INTERFERENCE RECEIVED, INCLUDING
INTERFERENCE THAT MAY CAUSE UNDESIRED
OPERATION.
Enter Master PIN code
Press
Press
Press
Feature Programming Through Menu Mode
Using Master PIN code*
Use this procedure only
when network primary
controller is missing or
otherwise inoperable.
