manualshive.com logo in svg

Yale YRC216, Инструкции по установке и программированию

Поделиться
Скачать
Yale YRC216 Скачать руководство пользователя страница 37

Yale Z

Plus Module

®

®

-Wave

Installation and Programming Instructions

Installing the Z

Plus Module

-Wave

®

This device is a security enabled Z-Wave Plus product that is able to use encrypted Z-Wave
Plus messages to communicate to other security enabled Z-Wave Plus products. This device
must be used in conjunction with a Security Enabled Z-Wave Controller in order to fully utilize
all implemented functions. This product can be operated in any Z-Wave network with other
Z-Wave certified devices from other manufacturers. All non-battery operated nodes within
the network will act as repeaters regardless of vendor to increase reliability of the network.

To Enroll/Add the Module (Inclusion Mode):

• Enter the 4-8 digit Master

code followed by the      key.

PIN

• Press the      key followed by the      key.
• Press the      key followed by the      key.

To Unenroll/Remove the Module (Exclusion Mode):

• Enter the 4-8 digit Master

code followed by the      key.

PIN

• Press the      key followed by the      key.
• Press the      key followed by the      key.

Factory Reset - If No Controller:

• See the Lock Installation Manual
• Please use this procedure only when the network primary controller is missing or

otherwise inoperable.

For System Integrators: Specific Z-Wave Plus association and parameter information for your
lock is available at YaleHome.com/ZwavePlus.

Enrolling/Unenrolling the Network Module:

IMPORTANT:

the batteries

be removed prior

must

to removing and/or inserting the network module:

• Remove battery cover and batteries.
• Remove and/or insert Network Module.
• Reinstall batteries and battery cover.

P/N

202-

-

-

Rev D

AYR

ZW INSTAL FUL

®

Содержание YRC216











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды