manualshive.com logo in svg

Yale YRC216, Инструкции по установке и программированию

Поделиться
Скачать
Yale YRC216 Скачать руководство пользователя страница 26

26

P/N

-

-

-

Rev B

YRL EMICL PBINSTL FUL

Hardware Troubleshooting

Cycle lock in both the locked and unlocked positions. If problems are found:

Bolt will not deadlock

a. Check for sufficient clearance of the bolt within the strike-side jamb.

Correct this by increasing the depth of the pocket for the bolt.

b. Check for misalignment of bolt and/or strike which may be preventing bolt

from properly entering the strike. With the door open, extend and retract the
bolt; if it is smooth, check the strike alignment.

Bolt does not extend or retract smoothly

a. Bolt and strike are misaligned, see above.
b. Check the backset of door relative to adjustments already made to bolt.
c. Verify proper door preparation and re-bore holes that are too small or

misaligned.

d. Verify keypad wire harness is routed properly (see Step 10).
e. Verify bolt is installed with correct side up (see Step 6).

Keypad numerics are scrolling

Remove interior lock and check to ensure that the wire harness is routed
properly (see Step 10).

Door is binding

a. Check that door and frame are properly aligned and door is free swinging.
b. Check hinges: They should not be loose or have excessive wear on knuckles.

Bolt will not extend and motor is grinding

a. Enter your Master

code.

PIN

b. With the bolt retracted, press menu Option 3 for Advanced Lock Settings.
c. Press Option 5 to rehand the lock.
d. Test the operation; locking the door via the keypad.

Содержание YRC216











































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды