manualshive.com logo in svg

Yale MSW020-E, Руководство по эксплуатации

Поделиться
Скачать
Yale MSW020-E Скачать руководство пользователя страница 89

Moving a Disabled Lift Truck

This lift truck is not normally towed. If the traction system
will not operate, make repairs at the location if possible. If
the lift truck must be towed, refer to the 

Maintenance Man-

ual

.

WARNING

Never carry a disabled lift truck unless the lift truck
MUST be moved. The lift truck used to lift the disabled
lift truck MUST have a rated capacity equal to or
greater than the weight of the disabled lift truck. The
capacity must be for a load center equal to half the
width of the disabled lift truck. See the capacity plate
on the disabled lift truck for the approximate total
weight. The forks must extend the full width of the dis-
abled lift truck. Put the weight of the disabled lift truck
at the center of the forks and be careful not to damage
the underside of the disabled lift truck. Tilt the mast
back and travel slowly.

WARNING

Make sure no one except the driver is near the lift
trucks during towing. Both the tow truck and the disa-
bled truck can cause a personal injury during towing.

WARNING

To avoid personal injury, use extra care when towing a
lift truck during the following conditions:

• Brake does not operate correctly.

• Steering does not operate correctly.

• Tire is damaged.

• Traction conditions are bad.

CAUTION

Never tow the lift truck faster than the speed of a per-
son walking. Steering can be difficult and motor dam-
age can occur at higher speeds. Always travel
smoothly without sudden starts.

To allow towing, the electric brake must be released by an
authorized technician before the lift truck can be moved. If
there is not sufficient battery power, placing the control
handle in the operating position will not release the electric
brake. Use the control handle to steer the lift truck while it
is being towed. Use one hand and walk to one side of the
lift truck. Do not walk or stand between the towing vehicle
and the lift truck.

Maintenance

87

Содержание MSW020-E



































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды