Yale GC030VX Скачать руководство пользователя страница 53 | Manualshive

Страница: 53 / 64

background image

Table 18. Proc_Cal_016: Transmission Valve Calibration (Continued)

If both Parking and Service Brakes are applied, you will
see.....

Calibrate Xmsn Valve
Press

*

to Begin.

NOTE:

Keep park brake applied, full service brake applied, and

full accelerator applied during entire time that automated transmis-
sion valve calibration is occurring.

Press

*

One Time

You Will See:

Calibrate Xmsn Valve
Done in 15

Watch display countdown. When completed successfully.....

You Will See:

Calibrations
Calibrate Xmsn Valve

Perform Proc_Cal_003: Save and Exit.

Proc_Cal_016A: Transmission Valve Calibration-Electronic

Extended Function

NOTE:

The information contained in the transmission

calibration procedures described below, apply to all lift
trucks covered in this YRM

EXCEPT

lift truck models:

•

GLP/GDP60VX, GLP/GDP70VX (GP/GLP/
GDP135VX,

GP/GLP/GDP155VX)

(C878,

D878, E878)

•

GLC/GDC60VX, GLC/GDC70VX (GC/GLC/
GDC135VX,

GC/GLC/GDC155VX)

(C879,

D879, E879, F879)

•

GLP/GDP80VX,

GLP/GDP80VX9,

GLP/

GDP90VX

(GLP/GDP170VX,

GLP/

GDP175VX36, GLP/GDP190VX) (A909, B909)

For the models listed above, see Proc_Cal_016B:
Trans. Valve Calibration-Electronic and Electronic Ex-
tended Function for calibration procedures.

APPLICABLE SYSTEM/OPTION

Electronic Power Shift Transmission

WHEN TO PERFORM

Performed whenever disassembling or replacing the
transmission, the transmission valve, or the transmis-
sion pressure sensors.

CALIBRATION ORDER

1.

Proc_Cal_001

NOTE:

Brakes must be properly adjusted and func-

tioning prior to performing this procedure.

2.

Proc_Cal_016A

WHY PERFORM

Performed to compensate for clutch pack control
valve pressure in relation to valve command current
tolerances.

HOW TO PERFORM

WARNING

Keep yourself and all others clear of the lift mech-
anism. Never allow anyone under or on the forks.

Never put hands, arms, head, or legs through the
mast or near the carriage or lift chains. This warn-
ing  applies  not  only  to  the  operator  but  also  the
helper. A helper must not be near the load or the
lift mechanism while the operator is attempting to
handle  a  load.  The  lift  mechanism  has  moving
parts  with  close  clearances  that  can  cause  seri-
ous injury.

WARNING

Keep  park  brake  applied,  full  service  brake  ap-
plied,  and  full  accelerator  applied  during  entire
time  that  automated  transmission  valve  calibra-
tion is occurring.

Refer to Table 19 for the procedures on how to per-
form Proc_Cal_016: Transmission Valve Calibration.

8000 YRM 1134

Proc_Cal_016: Transmission Valve Calibration

Confidential/Proprietary - Do Not Copy or Duplicate

47

«
...
51
52
53
54
55
...
»

Содержание GC030VX

































































Отзывы:

Нет отзывов

Похожие инструкции для GC030VX

Бренд: ABB Страницы: 14

D-MAS HyperSat 2540

Бренд: DanMedical Страницы: 103

Бренд: AcceleDent Страницы: 3

Бренд: Zero 88 Страницы: 32

Бренд: ParaBody Страницы: 6

Бренд: Sailmon Страницы: 10

Бренд: B&W Tek Страницы: 12

Бренд: b&o Страницы: 46

Бренд: iHealth Страницы: 8

Бренд: Omlet Страницы: 2

Бренд: Omicron Страницы: 382

Бренд: Omicron Страницы: 188

Бренд: P-Q Controls Страницы: 5

Бренд: P+L Systems Страницы: 2

Бренд: TC Electronic Страницы: 67

Бренд: Tascam Страницы: 3

Бренд: RainPoint Страницы: 40

Бренд: FARM-MAXX Страницы: 35

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды