background image

FTV-1000 Operating Manual

Page 1

The 

FTV-1000

 is a high-performance, high-power 50-54 MHz transverter compatible with the Yaesu 

MARK-V

FT-1000MP transceiver. Providing excellent receiver performance and up to 200 Watts of power output, the 

FTV-

1000

 is specifically designed for the demanding requirements of 50 MHz DX operators.

Among the leading-edge features of the 

FTV-1000

 is a Class-A operating bias selection for the transmitter’s

power amplifier stage; during Class-A operation, power output is reduced to 50 Watts, and the high bias current
leads to an extraordinarily clean SSB wave-form, with 5

th

-order intermodulation (IMD) typically suppressed by at

least 65 dB.

The 

FTV-1000

’s feature complement includes selectable receiver preamplifiers, two antenna jacks, Intercept

Point Optimization (direct feed to mixer during strong signal conditions), and convenient interface jacks for acces-
sories.

The 

FTV-1000

 is fully compatible with Yaesu’s 

VL-1000

 Quadra System Linear Amplifier, which includes cover-

age of the 50 MHz band. The 

MARK-V

 FT-1000MP, 

FTV-1000

, and 

VL-1000

 provide unparalleled performance on

all bands between 1.8 and 54 MHz, and especially on the six meter band.

Thank you for your investment ion the 

FTV-1000

! We recommend that you read this manual thoroughly, so as to

understand fully the features and the operating procedures that will ensure that you get the most out of your leading-
edge Yaesu 50 MHz station!

Introduction

Supplied Accessories

DC POWER

 Cable (T9022699; 1.2 m) ............................................................................................................. 1

ANTENNA

 Cable (T9101513; M-type 

 M-type, 1.2 m) .................................................................................. 1

BAND DATA

 Cable (T9101510; 8-pin DIN 

 8-pin DIN, 1.2 m) ....................................................................... 1

ALC

 Cable (T9101514; “GRAY” RCA 

 “GRAY” RCA, 1.2 m) ........................................................................ 1

TRV

 Cable (T9101515; “BLACK” RCA 

 “BLACK” RCA, 1.5D2V 1.2 m) ........................................................ 1

Operating Manual ............................................................................................................................................. 1
Warranty Card ................................................................................................................................................... 1

Содержание FTV-1000

















Отзывы: