FT
DX
9000 TFT O
PERATION
M
ANUAL
B
EFORE
U
SING
THE
TFT D
ISPLAY
“MY Screen” Setup
The groups are as follows.
1.
AGC
:
2.
DISPLAY
:
3.
FH-2
:
4.
GENERAL
:
5.
MODE-AM
,
MODE-CW
,
MODE-DATA
,
MODE-DM
,
MODE-PKT
,
MODE-RTTY
,
MODE-SSB
6.
RX AUDIO
:
7.
RX DSP
: RX Filter bandwidth and shaping
8.
SCOPE
: Setup of the starting frequency for the
Spectrum Scope
9.
TUNING
: Setup of the Dial steps
10.
TX AUDIO
: Setup of the Parametric Equalizer
11.
TX GNRL
:Setup of the
For detailed information regarding the Menu mode,
please see the “How to Use the Menu Mode” section
of this manual, and the operation manual of the radio.
M
ENU
M
ODE
R
ESET
It is possible to reset (only) the Menu mode set-
tings back to their factory default. Do this if you
want to clear all settings out, and start fresh with
the original values.
1. Turn off the radio.
2. Turn the radio on while pressing and holding
in the [
MNU
] key.
Page 3
O
PERATION
OF
THE
TFT S
CREEN
If you want to change a configuration setting of this
radio, you are able to display the Menu mode on the
TFT screen, so you can change it efficiently. In order
to enter the “Menu” mode, press the [
MNU
] key mo-
mentarily; the Menu screen will now appear on the
screen. By rotating the Main Tuning knob, you can
move to the desired item you want to change now you
can choose the revised setting by rotating the
CLAR/
VFO-B
knob. It is also possible to move the Menu
items and values by pressing the function keys lo-
cated below the TFT screen. For details, please refer
to “How to Use the Menu Mode.”
When you have completed the changes to the Menu
item(s), press and hold in the [
MNU
] key for 2 sec-
onds; the setting(s) will now be saved. If you do not
want to save the new setting, press the [
MNU
] key
momentarily; the radio will revert to its previous condi-
tion.
There are 176 items in the Menu mode, and they are
grouped; the group name is displayed at the left top of
the list screen. It will be convenient for you if you ini-
tially select the group, by rotating the Main Tuning
knob, and
then
select the item you want.
M
ENU
M
ODE
O
PERATION
1. Press the [
MNU
] key to enter the Menu mode.
2. Rotate the [
Main Tuning Dial
] knob to select
Menu item DISPLAY “021:
MY SCREEN
”.
3. Rotate the [
CLAR/VFO-B
] knob to choose a
screen you wish to omit (skip) from the screen
selection loop.
4. Press the [
ENT
] key to set the omission com-
mand to “ON”.
5. Repeat steps 3 and 4 to select/deselect as
many screens as you like.
Note
: The “ON” command sets the selected
screen to be skipped, while the “OFF” com-
mand sets the selected screen to be included
in the screen selection loop.
6. Press and hold in the [
MNU
] key for two sec-
onds to store the new number and exit to nor-
mal operation.
You may want to select more than one screen while
in “My Screen”. If you select only one screen, you
will not be able to call any other screens when you
press the [
DISP
](
DISPLAY
) key.
