Yaesu Contest, Руководство по эксплуатации

Страница: 17 / 54

FT
DX
9000MP/C
ONTEST
D
ATA
M
ANAGEMENT
O
PERATION
M
ANUAL
S
PECTRUM
S
COPE
25 kHz 50 kHz 100 kHz 250 kHz
500 kHz 1000 kHz 2500 kHz 25 kHz ......
[
3/5
](
ATT
) “Attenuator”
By pressing this key, the attenuation can be
switched as shown below. The noise level on the
band will vary according to conditions, your an-
tenna, the time of day, etc.; please select the ap-
propriate value for current conditions.
0 dB 10 dB 20 dB 0 dB ......
[
4/7
](
A/B
)
Selects the VFO which is to be shown.
In the case of “Single” display, the Main (VFO-A)
and Sub (VFO-B) VFOs can be toggled alternately.
In the “Dual” mode, both VFOs will be shown.
Advice : In the case of the Contest version, the RX
switch to the left of the CLAR/VFO-B knob will,
when pushed, cause both the VFO itself and the Spec-
trum Scope display to change to VFO-B. Additionally,
when the optional RXU-9000 Dual Receive Unit is in-
stalled, you may use the [4/7](A/B) key to make this
change, just like on the MP version.
[
5/10
](
DUAL
)
This key switches between Single and Dual VFO
Spectrum Scope display. When Dual is selected,
the Main VFO will occupy the upper position, and
the Sub VFO the lower.
When this key is pressed once more, the radio will
revert to “Single” display. If you want to change
the setup of a Spectrum Scope VFO, press the [
4/
7
](
A/B
) key. In this case, the frame will move to
the upper side or lower side. Select the side which
you want to change, then press the [
3/5
](
ATT
) key
or the [ 2/3.5
](
SPAN
) key to change those respec-
tive settings just for the selected VFO.
In the Dual display mode, when you want to con-
firm the setup situation, press the [
6/14
](
STATUS
)
key to show the current settings for that screen.
Press the key once again to make the setup
screen disappear.
Advice : In the Contest version, if the optional RXU-
9000 dual Receive Unit is installed, you may also
choose the “Dual” A/B VFO split Spectrum Scope dis-
play, just like on the MP version.
[
6/14
](
CTR/FIX
)
By pressing this key, it is possible to switch be-
tween the CTR mode and FIX mode.
In the CTR mode, the current operating frequency
is displayed at the center of the screen; in the FIX
mode, the frequency selected via the Menu is fixed
at the left edge of the display.
Advice : In either CTR or the FIX mode, the current
operating frequency is indicated on the screen by
the yellow arrow (
), for ease of status recognition.
[
7/18
](
LBWS
)
Press this key to activate the “Limited Band Width
Sweep” (LBWS) function, which permits high-
speed sweeping of a band segment.
As the bandwidth is set narrower, the sweep
speed becomes faster, allowing the scope to cap-
ture signals with quicker resolution. The band-
width can be set to 50 %, 30 % or 10 % of the full
span. The sweep speed becomes faster by the
following amounts:
50 %: about 2 times faster
30 %: about 3 times faster
10 %: about 10 times faster
NORMAL LBWS-1(50%)
LBWS-2(30%) LBWS-3(10%) NORMAL ......
Advice : When you enter the LBWS mode, the
function keys below the Display change.
It is possible to move the sweep position by press-
ing the [
5/10
]( ) and [
6/14
]( ) key.
If you want to return to normal operation, press
[
6/14
](
LBWS
) key as needed.
Please note that LBWS can not be used in the FIX
mode. Please use LBWS only in the CTR mode.
[
8/21
](
DISPLAY
)
Press this key to switch the Display to the “ A
UDIO
S
COPE
/O
SCILLOSCOPE
” screen.
Press and hold in this key to switch the Display to
the “
W
ORLD
C
LOCK
” screen.
E
XPLANATION OF THE
F
UNCTION
K
EYS ON THE
S
PECTRUM
S
COPE
S
CREEN
FIX M
ODE
S
ETUP
(
L
EFT
E
DGE
F
REQUENCY
)
Press the [ MNU ] key momentarily to enter the Menu
mode. Select the item which you want to change
by rotating the Main Tuning knob (in this case, the
item will be one of the items in the range from
SCOPE “108:
MAIN FIX 1.8 MHz ” to “129: SUB
FIX 50MHz ”). Then change the setting by rotating
the CLAR/VFO-B knob.
When the change is completed, press and hold
in the [ MNU ] key for 2 seconds to save the change.
If you do not want to save the change, press the
[
MNU ] key momentarily. The radio will go back to
the previous condition/situation.
There are many setup items in the Menu mode,
and they are grouped for easy recognition; the
group name is displayed at the top left corner of
the list screen. It is usually more convenient if you
initially select the group by rotating the Main Dial,
and then select the item you want.
Page 15