background image

Item# 610174 Dwg# 610174

March 2021 Rev A

1725 Brannum Lane
Yellow Springs, OH 45387 
(800) 765-4974,  (937) 767-7241 
[email protected]

YSI.com

 Powering the Logger

The ProSwap Logger comes in two versions: one with an internal, rechargeable lithium ion 
battery and one without internal power.

Internal Battery

A fully charged internal battery should last at least 90 days at a 15 minute logging interval. 
Battery life will vary depending on which ProDSS Sensor is installed.

The battery may be recharged via connection to a power source including a handheld, USB 
adapter, or external power supply. Full recharge time may take up to 14 hours depending on the 
power source.

External Power 

For the non-battery logger, or to charge the battery version, there are several options to supply 
power (these options are all sold separately):
•  ProSwap or ProDSS Handheld – The handheld will power the logger as long as it is connected 

and powered on. 

•  ProSwap Logger AA Power Pack – The power pack utilizes six AA batteries to provide power to 

the logger for at least 90 days at a 15 minute logging interval.

•  USB Adapter – The USB Adapter will power the logger when connected to a PC USB port or 

AC adapter.

•  Flying Lead Adapter – The flying lead adapter may be used to supply external power and 

provide communication with a data logger.

 Connection to Kor Software via USB Adapter or Handheld

The ProSwap Logger can be connected to a PC running Kor Software via a USB adapter. A 
ProDIGITAL USB adapter is sold separately. Additionally, the software communication may be 
established through the handheld’s USB port.

1. 

Install Kor Software from the included USB Drive or 
download the latest version from 

YSI.com

. Follow 

the prompts to install the new drivers.

2. 

Connect the ProSwap Logger to a USB adapter or 
handheld.

3. 

Connect the USB cable to the PC to establish 
communication.

4. 

Check for firmware updates.

The USB connection provides communication and power to the ProSwap Logger. Loggers with 
internal battery may be charged via this connection.

AA

AA

AA

AA

AA

AA

Содержание YSI Pro Swap Logger

Страница 1: ...nd depth sensors and it is designed for use with any single ProDSS digital smart sensor NOTE Turbidity and Total Algae sensors must be used with the Extended Probe Guard 626740 sold separately Refer to the ProSwap Logger User Manual for Part numbers and accessories Maintenance guidelines Sensor calibration instructions Connecting ProSwap Logger to a data logger AA AA AA AA AA AA AA Item Numbers 61...

Страница 2: ...r Probe Guard Storage Sleeve Sponge Graduated Cylinder USB Drive contains Kor Software Cable Connector Cap Cable Grip Kit Cable Management Kit 4m 10m 20m or Cable Spool 30m Maintenance Kit Desiccant Kit Vented units ONLY Unpacking and Inspection Inspect the outside of the shipping container s for damage If you see any damage contact the shipping carrier immediately Carefully remove the equipment f...

Страница 3: ...mperature and depth sensors in addition to a single port The port will allow any ProDSS smart sensor to be connected 1 Remove the port cover shipped with the cable 2 Apply a thin coat of lubricant to the sensor o rings 3 Carefully align the sensor and bulkhead connectors by inserting the sensor into the port then gently rotating the sensor until the connectors align Once aligned push the sensor to...

Страница 4: ...red on ProSwap Logger AA Power Pack The power pack utilizes six AA batteries to provide power to the logger for at least 90 days at a 15 minute logging interval USB Adapter The USB Adapter will power the logger when connected to a PC USB port or AC adapter Flying Lead Adapter The flying lead adapter may be used to supply external power and provide communication with a data logger Connection to Kor...

Отзывы: