background image

materials, coatings and other "wear parts" or consumables all of which are not warranted

except as otherwise provided in the quotation or sales form) will be free from defects in

material and workmanship for a period of one (1) year from the date of installation or

eighteen (18) months from the product date code, whichever shall occur first, unless a longer

period is provided by law or is specified in the product documentation (the “Warranty”).
Except as otherwise required by law, Seller shall, at its option and at no cost to Buyer, either

repair or replace any product which fails to conform with the Warranty provided Buyer gives

written notice to Seller of any defects in material or workmanship within ten (10) days of the

date when any defects or non-conformance are first manifest. Under either repair or

replacement option, Seller shall not be obligated to remove or pay for the removal of the

defective product or install or pay for the installation of the replaced or repaired product and

Buyer shall be responsible for all other costs, including, but not limited to, service costs,

shipping fees and expenses. Seller shall have sole discretion as to the method or means of

repair or replacement. Buyer’s failure to comply with Seller’s repair or replacement directions

shall terminate Seller’s obligations under this Warranty and render this Warranty void. Any

parts repaired or replaced under the Warranty are warranted only for the balance of the

warranty period on the parts that were repaired or replaced. The Warranty is conditioned on

Buyer giving written notice to Seller of any defects in material or workmanship of warranted

goods within ten (10) days of the date when any defects are first manifest.
Seller shall have no warranty obligations to Buyer with respect to any product or parts of a

product that have been: (a) repaired by third parties other than Seller or without Seller’s

written approval; (b) subject to misuse, misapplication, neglect, alteration, accident, or

physical damage; (c) used in a manner contrary to Seller’s instructions for installation,

operation and maintenance; (d) damaged from ordinary wear and tear, corrosion, or

chemical attack; (e) damaged due to abnormal conditions, vibration, failure to properly

prime, or operation without flow; (f) damaged due to a defective power supply or improper

electrical protection; or (g) damaged resulting from the use of accessory equipment not sold

or approved by Seller. In any case of products not manufactured by Seller, there is no

warranty from Seller; however, Seller will extend to Buyer any warranty received from

Seller’s supplier of such products.
THE FOREGOING WARRANTY IS PROVIDED IN PLACE OF ALL OTHER EXPRESS

WARRANTIES. ALL IMPLIED WARRANTIES, INCLUDING BUT NOT LIMITED TO THE

IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR

PURPOSE, ARE LIMITED TO ONE (1) YEAR FROM THE DATE OF INSTALLATION OR

EIGHTEEN (18) MONTHS FROM THE PRODUCT DATE CODE , WHICHEVER SHALL

OCCUR FIRST. EXCEPT AS OTHERWISE REQUIRED BY LAW, BUYER’S EXCLUSIVE

REMEDY AND SELLER’S AGGREGATE LIABILITY FOR BREACH OF ANY OF THE

FOREGOING WARRANTIES ARE LIMITED TO REPAIRING OR REPLACING THE

PRODUCT AND SHALL IN ALL CASES BE LIMITED TO THE AMOUNT PAID BY THE

BUYER FOR THE DEFECTIVE PRODUCT. IN NO EVENT SHALL SELLER BE LIABLE

FOR ANY OTHER FORM OF DAMAGES, WHETHER DIRECT, INDIRECT, LIQUIDATED,

INCIDENTAL, CONSEQUENTIAL, PUNITIVE, EXEMPLARY OR SPECIAL DAMAGES,

INCLUDING BUT NOT LIMITED TO LOSS OF PROFIT, LOSS OF ANTICIPATED

SAVINGS OR REVENUE, LOSS OF INCOME, LOSS OF BUSINESS, LOSS OF

PRODUCTION, LOSS OF OPPORTUNITY OR LOSS OF REPUTATION.
Some states do not allow limitations on how long an implied warranty lasts, so the above

limitation may not apply to you. Some states do not allow the exclusion or limitation of

incidental or consequential damages, so the above exclusions may not apply to you. This

warranty gives you specific legal rights, and you may also have other rights which may vary

from state to state.
To make a warranty claim, check first with the dealer from whom you purchased the product

or visit www.xyleminc.com for the name and location of the nearest dealer providing

warranty service.

8  Product Warranty

Series e-80SCXL INSTRUCTION MANUAL

33

Содержание Bell & Gossett e-80SCXL Series





































Отзывы: