manualshive.com logo in svg

Xylem 7030.090, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem 7030.090 Скачать руководство пользователя страница 7

Electrical hazard

Magnetic fields hazard

Electrical Hazard:
 

CAUTION:
 

1.3  User safety

All regulations, codes, and health and safety directives must be observed.

The site

• Observe lockout/tagout procedures before starting work on the product, such as

transportation, installation, maintenance, or service.

• Pay attention to the risks presented by gas and vapors in the work area.
• Always be aware of the area surrounding the equipment, and any hazards posed by the

site or nearby equipment.

Qualified personnel

This product must be installed, operated, and maintained by qualified personnel only.

Protective equipment and safety devices

• Use personal protective equipment as needed. Examples of personal protective

equipment include, but are not limited to, hard hats, safety goggles, protective gloves and

shoes, and breathing equipment.

• Make sure that all safety features on the product are functioning and in use at all times

when the unit is being operated.

1.4  Ex-approved products

Follow these special handling instructions if you have an Ex-approved unit.

Personnel requirements

These are the personnel requirements for Ex-approved products in potentially explosive

atmospheres:

• All work on the product must be carried out by certified electricians and Xylem authorized

mechanics. Special rules apply to installations in explosive atmospheres.

• All users must know about the risks of electric current and the chemical and physical

characteristics of the gas, the vapor, or both present in hazardous areas.

• Any maintenance for Ex-approved products must conform to international and national

standards (for example, IEC/EN 60079-17).

Xylem disclaims all responsibility for work done by untrained and unauthorized personnel.

Product and product handling requirements

These are the product and product handling requirements for Ex-approved products in

potentially explosive atmospheres:

• Only use the product in accordance with the approved motor data.
• The equipment must never run dry during operation. The volute must be filled with liquid

during operation. Dry running during service and inspection is only permitted outside the

classified area.

• Before you start work on the product, make sure that the product and the control panel

are isolated from the power supply and the control circuit, so they cannot be energized.

• Do not open the product while it is energized or in an explosive gas atmosphere.
• Intrinsically safe circuits are normally required for the automatic level-control system by

the level regulator if mounted in zone 0.

• The yield stress of fasteners must be in accordance with the approval drawing and the

product specification.

1  Introduction and Safety

P7030, P7035, P7040 Installation, Operation, and Maintenance Manual

5

Содержание 7030.090

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды