manualshive.com logo in svg

Xylem 7030.090, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Xylem 7030.090 Скачать руководство пользователя страница 61

5  Operation

5.1  Precautions

Before taking the unit into operation, check the following:

• All recommended safety devices are installed.
• The cable and cable entry have not been damaged.
• All debris and waste material has been removed.

NOTICE:
Never operate the pump with the discharge line blocked, or the discharge valve closed.

WARNING: Crush Hazard
Risk of automatic restart.

Distance to wet areas

WARNING: Electrical Hazard
Risk of electrical shock or burn. You must connect an additional ground- (earth-) fault

protection device to the grounded (earthed) connectors if persons are likely to come into

contact with liquids that are also in contact with the pump or pumped liquid.

CAUTION: Electrical Hazard
Risk of electrical shock or burn. The equipment manufacturer has not evaluated this unit for

use in swimming pools. If used in connection with swimming pools then special safety

regulations apply.

Noise level

NOTICE:
The sound power level of the product is lower than 70 dB(A). However, in some installations

the resulting sound pressure level may exceed 70 dB(A) at certain operating points on the

performance curve. Make sure that you understand the noise level requirements in the

environment where the product is installed. Failure to do so may result in hearing loss or

violation of local laws.

5.2  Estimate zinc anode replacement intervals

The mass and surface area of the zinc anodes are designed to protect the pump surface for

1 year in sea water with an average temperature of 20°C (68°F). Shorter inspection intervals

and anode replacement can be required, depending upon the water temperature and the

chemical composition as well as the presence of other metals in the vicinity of the pump.
The rate of zinc consumption, and the appropriate inspection intervals, can be estimated by

measuring how much zinc is consumed during the first two months following installation.
Anodes are replaced when the anode mass is reduced to a selected fraction of its initial

mass. The recommended interval for the selection fraction is 0.25–0.50 (25–50%).
1. Remove, weigh, and reinstall one or more of the exterior zinc anodes before starting up

the pump.

2. After two months, remove and weigh the same zinc anode or anodes again.
3. Divide the lapsed time in days (between steps 1 and 2) by the anode weight loss in

grams to get the calculated anode consumption rate (days/gram).

5  Operation

P7030, P7035, P7040 Installation, Operation, and Maintenance Manual

59

Содержание 7030.090

























































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды