Xycom 3400 Series Скачать руководство пользователя страница 93 | Manualshive

Страница: 93 / 99

background image

93

Appendix D – Installing the IDE Flash Drive

As an additional storage option, you can install an IDE flash drive on your 3408/3410
unit.

Installing the IDE Flash Drive

Warning

You must disconnect the power cable, as well as any other external ca-
bles connected to the unit, before removing the back cover.

Perform the following steps to replace the IDE Flash drive:

1.

Disconnect the power cable, as well as any other external cables.

2.

Unscrew the three back cover mounting screws (refer to the back panel figures in
Chapter 3 if you need help locating these screws).

3.

Slide the back cover toward the I/O panel, and lift off.

4.

Disconnect the cable connected to the touchscreen connector (TCH1) at the top of
the unit or the keypad connector and the display cable under the power supply.

5.

Loosen the four screws holding the flat-panel display carrier to the front panel.
These screws remain attached to the carrier.

6.

Carefully lift off the carrier.

7.

Flip the unit over to expose the flat-panel display.

8.

Disconnect the two bulb connectors (pink and white wires) on the right-hand side of
the display.

9.

Remove the four screws attaching the display to the front-panel standoffs.

10.

Place the flat-panel display face down on a protective surface.

11.

Remove the four screws and lift off the hard drive.

12.

Remove the Flash drive card by pushing down on the piece of metal and pulling out
the card. Replace with the new Flash drive card, as shown in Figure D-1.

«
...
91
92
93
94
95
...
»

Содержание 3400 Series




































































































Отзывы:

Нет отзывов

Похожие инструкции для 3400 Series

Бренд: XpressFill Страницы: 11

Cutler-Hammer ATC-300

Бренд: Eaton Страницы: 32

Бренд: Eaton Страницы: 2

Бренд: Jaeger Страницы: 36

Бренд: Lavorwash Страницы: 26

Teleline Isolator 751239

Бренд: Positron Страницы: 20

Бренд: Wachs Страницы: 44

Бренд: Pentair Страницы: 16

Бренд: Dynapac Страницы: 25

Бренд: Graco Страницы: 40

ELCOROCK FILLING FRAME

Бренд: GEOFABRICS Страницы: 7

Бренд: ebm-papst Страницы: 14

Бренд: Zilmet Страницы: 6

Бренд: Jäger Страницы: 36

Mini Filter Wheel with OAG

Бренд: Starlight Xpress Страницы: 7

Бренд: R.V.R. Elettronica Страницы: 168

Бренд: Liberty Pumps Страницы: 8

Бренд: Kval Страницы: 40

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды