manualshive.com logo in svg

Xtreme Power 82100, Инструкция по эксплуатации и правила безопасности, Страница: 6 / 16

Поделиться
Скачать
Xtreme Power 82100 Скачать руководство пользователя страница 6

5

GUIDE BAR AND SAW CHAIN PARTS LIST

: A standard chainsaw unit package contains the 

items illustration in Figure F1. Open the box and install the guide bar and the saw chain on the 

power unit as follows. 
1. POWER UNIT
2. BAR PROTECTOR

4. CHAINSAW
5. PLUG WRENCH
6. SCREWDRIVER FOR CARBURETTOR ADJUSTMENT
7. SPIKE AND MOUNTAIN SCREWS

The chainsaw has very sharp edges. Use thick protective gloves for safety. 
WARNING: 

The features include on your chainsaw are to help prevent the hazard of kickback; however, 

such features will not eliminate this danger. As a chainsaw user, do not rely only on safety devices 

alone. You must follow all safety precautions, instructions and maintenance in this manual to help avoid 

kickback and other forces which can result in serious bodily injury. 

3. GUIDE BAR

1. 

Pull the guard towards the front handle to check the 

chain brake is not on.

2.

 Loosen the nuts and remove the chain cover. 

4. 

Gear  that  chain  to  the  sprocket  and  while  fitting  the 

chain saw around the guide bar, mount the guide bar to 

the power unit. Adjust the position of the chain tensioner 

nut on the chain cover to the lower hole of the guide bar. 

(F2)

3. 

Install the attached spike to the power unit.

 (8) Hole   (9) Tensioner Nut  (10) Chain Cover

1

. Moving direction

2.

 Fit the chain cover to the power unit and fasten the nuts 

to finger tightness. 

4. 

Tighten the nuts securely with the bat tip held up (12-

15N.m). Then check the chain for smooth rotation and 

proper  tension  while  moving  it  by  hand.  If  necessary, 

readjust with the chain cover loose. 

3. 

While  holding  up  the  tip  of  the  bar,  adjust  the  chain 

tension by turning the tensioner screw until the tie straps 

just touch the bottom side of the bar rail. (F4)

Pay attention to the correct direction of the saw 

chain. (F3)

5. 

Tighten the tensioner screw.

(2) Loosen    (3) Tighten   (4) Tensioner Screw

DIAGRAMS AND SPECIFICATIONS

Содержание 82100

















Отзывы:

Нет отзывов