background image

2

Visit our website at http://xtm.globalhobby.com or for Customer Service at http://globalservices.globalhobby.com

ENGINE WARNINGS

Never use any fuel in your engine other than glow fuels

specifically designed for use in model car engines.  Use of any
other types of fuel can cause severe damage to the engine and/or
personal injury.  

NEVER USE GASOLINE OR DIESEL FUEL!

Never operate your model on any public streets.  This could

cause traffic accidents, personal injury or property damage.

Glow fuel engines emit exhaust vapors that are poisonous and

can be dangerous to your health.  It is important that you operate
your engine in a very well-ventilated area, preferably outdoors.

Before starting the engine, make sure that the throttle trim is

set to the idle position.  Starting the engine at any setting above
idle can cause the model to lurch out of your hands.

When the engine is running, there are certain parts that rotate

at high speeds.  Be careful not to touch the drive shafts, gears,
clutch assembly or any other moving parts.  Otherwise, serious
injury could result.

It is normal for the engine, exhaust header and tuned pipe to

get very hot during operation.  Never touch these parts while
they are hot or you might be burned.

Model car engines produce vibration when they are running.  It

is important to periodically check the engine mounting screws
and other assemblies to ensure they are tight.  Running the
engine with the engine mounting screws loose can lead to
severe engine and/or chassis damage.

FUEL WARNINGS

Glow fuels like those used in your Mammoth RTR Nitro

Monster Truck are poisonous.  Follow all the precautions that
are printed on the fuel manufacturer's container.

Keep fuel out of the reach of children.

Glow fuel is extremely flammable.  Keep away from high heat,

sparks and flame.

GENERAL WARNINGS

Under no circumstances should you operate your model in

crowds of people.  Serious injury could result.

Never operate your model on busy streets or if there are cars

around.

Do not use your model to chase pets or other animals.

The radio system included in your model is not waterproof;

therefore, do not drive through water, wet grass, mud or snow.

Because your model is operated by radio control, it is important

to make sure you always are using fresh and/or fully charged
batteries.  Never allow the batteries to run low or you could lose
control of the model.

If your model becomes stuck, allow the engine to idle, then

retrieve your model by hand.

To prevent excessive r.p.m.'s from damaging the engine and/or

drive-train components, we suggest reducing throttle while in the
air during jumps.

If you should have any trouble with any of the steps listed in this Operations Guide, we have provided an extensive troubleshooting guide
beginning on page # 16.  The troubleshooting guide is provided to help you find a quick and immediate resolution to a number of
problems that might occur.  If you cannot solve a problem using the troubleshooting guide, or if you have any other questions or
concerns, please contact us at the address below:

FOR YOUR INFORMATION

FOR YOUR SAFETY - PLEASE READ THESE WARNINGS FIRST!

Visit Our Website

http://globalservices.globalhobby.com

Global Services
18480 Bandilier Circle
Fountain Valley CA  92708

Phone: (714) 963-0329          Fax: (714) 964-6236           Email: [email protected]

To allow us to serve your needs better, please include your email address with any correspondence you send to us.  Your email address will be added to our Customer
Service Database so you will automatically receive free updates and tech notices for your particular product.  You will also receive repair status updates (if applicable) and
other important information about your product as it becomes available.

IMPORTANT INFORMATION ABOUT YOUR EMAIL ADDRESS

Global Hobby Distributors will not disclose the information it collects to outside parties.  Global Hobby Distributors does not sell, trade, or rent

your personal information to others . Your privacy is important to us.

CHECK IT OUT!

  We urge you to come check out our website at http://globalservices.globalhobby.com.  There you will find public message boards

frequented by other XTM Racing product owners and the XTM Racing support staff.  This is a great place to learn about new XTM Racing products,
get help and suggestions for your current XTM Racing products or just simply hang out and chat with people that share your same interests.

Содержание Mammoth





















Отзывы: