background image

  

 

3-2

 Installation

 

 

"

      

Installing two new Hard Disks

 

 

1. After finishing hardware installation, turn the power on. In the BIOS setting screen, change 

HDD type to AUTO. This will enable the computer system to automatically detect the type 
and model of your Hard Disks.

 

 

2. After restarting the computer, the XL-RAID133v2 will automatically low format HDD 

synchronously. In addition, it will install the OS and other required software. (Refer to OS 
Installation Guide) 

3. If the two installed hard disks have different capacities, XL-RAID133v2 will auto detect 

and set the capacity according to the smaller one. This way your Computer will suppose 
that the XL-RAID133v2 has a smaller capacity. 

   

"

        

Installing one new HDD in Auto-Rebuild mode

 (Setup RAID1) 

 

1. Locate the original HDD in either the upper or lower deck of XL-RAID133V2 . 

2. In the event of no HDD inside, XL-RAID133v2’s buzzer begins to sound after 

computer is started. To switch off the alarm, use a sharp pointed object to turn off the 
buzzer on the front panel. The Access LED on the lower part of the panel will be on. 
(Note 1) 

3. After loading the OS, insert the Removable Carrier with the new HDD into the upper 

or lower deck of the XL-RAID133v2. The capacity of the new HDD should be equal 
to or greater than the original one. 

4. Wait a few minutes, after which the XL-RAID133v2 will automatically perform the 

Auto-Rebuild 

function.

 

 

5. After the 

Auto-Rebuilding

, use a sharp pointed object to turn on the buzzer on the 

front panel. The Access LED on the lower part of the panel will be off. (Note 2) 

 

 

"

        

Hot plug and data on-line rebuild under RAID Level 1

 

 

1.

    

In the event of any installed HDD’s operation failure, the XL-RAID133v2 buzzer will 

sound. Pull out the Removable Carrier together with the damaged HDD without 
turning the power off. 

2.

    

PC will continue normally to store data into the other HDD; no data loss will happen. 

12

 

 

Содержание XL-RAID133v2
























Отзывы: