• Turn the volume control knob fully counterclockwise.
• First, connect all the audio input devices to the loudspeaker. Make sure all
input sources (microphones, CD players, digital media players) are turned off
and the volume settings are set to their lowest level.
• Connect the loudspeaker to a power source (if the speaker is not being used
in battery mode).
• Turn the power switch to the ON position.
• Turn the volume (of the loudspeaker and all the audio sources) clockwise until
the sound output is at the desired level.
Note: If there is no sound, check to make sure the source equipment is
providing audio.
Note: For your safety, read this manual and follow all safety instructions before
using this product.
IV. Initial setup
Auxiliary mode operation
Recommendation: The supplied 3.5mm to 3.5mm auxiliary cable has to be
used to enable audio playback from devices fitted with an auxiliary 3.5mm jack.
a. Set the loudspeaker to the LINE IN mode by pressing the MODE button on
the control panel. (A voice prompt will indicate Line-in mode).
b. Connect one side of the 3.5mm auxiliary cable to the auxiliary port on the
speaker and the other side of the cable to the audio source of choice.
c. Start streaming audio files directly from the audio source of choice. Press the
Play/Pause button, to play or pause the audio.
MicroSD
TM
/USB mode operation
Recommendation: Use a USB flash drive or micro-SD
TM
card to enable audio
playback from compatible files stored in this type of devices.
a. First, connect a USB flash drive or MicroSD™ card to the port of the
speaker.
b. The loudspeaker will automatically change to the USB or MicroSD™ mode
when the source device is connected. If this does not happen set the
loudspeaker to the MicroSD™ or USB mode by pressing the MODE button
on the control panel. (A voice prompt will indicate the mode corresponding
to the audio source inserted: MicroSD™ or USB).
c. Start streaming audio files directly from the source of choice. Press the
Play/Pause button, to play or pause the audio.
FM tuner mode operation
a. Press the Mode button to toggle through the different modes available until
the FM tuner mode is prompted.
b. Press and hold the Play/Pause button to initiate the scanning of channels
from the lowest up to the highest frequency, and store them automatically as
presets in the memory. The FM indication will be displayed during this
process and the speaker will automatically save the searched station and
store it in P01, P02, P03, etc. Press the Play/Pause button briefly again to
stop the search at any time.
c. Once the searching process has been completed, the unit will automatically
select P01. Press the Previous track or Next track buttons to switch to a
different radio station. Press the Play/Pause button briefly to mute the
stations, the FM indication will be displayed.
Note: If during the FM mode operation a USB flash drive or MicroSD™ card
is connected, the system will automatically switch to USB/MicroSD™ mode.
Press the Mode button to go back to FM mode.
VI. Advanced operation
Pairing the speaker with wireless devices
Note: Before installing this product, please make sure your device is
compatible with Bluetooth
®
.
1. Turn the power switch on located on the Media panel of the unit. Hi will
appear on the screen.
2. Enable the Bluetooth
®
feature on your audio device and set it to discover the
wireless speaker.
3. Remember to place your wireless device and the speaker not more than one
meter away from each other.
4. Next, cycle to the Bluetooth
®
feature on the speaker by pressing the MODE
button found on the media panel and select it as the input source. The
unit will emit a short tone followed by a blinking "bLUE" word on the LED
panel to indicate that the speaker has entered into the pairing mode.
5. Once the speaker appears listed under the newly found Bluetooth
®
devices
(XTS-702) of your wireless device, it will ask if you want to pair with it.
6. Accept by pressing Yes or Ok. If you have a lower Bluetooth
®
version, you
may be prompted to enter the passkey 0000 (4 zeros).
Charging the battery
• When the unit is not in use or switched off, it will automatically recharge the
internal battery as long as it remains connected to the power source.
• While charging, the LED lights up in red. When the battery has reached full
capacity, the light will turn green.
• Turn off the loudspeaker when not in use to conserve battery life.
V. Operating modes
