Xray T2R PRO, Инструкция по эксплуатации

Страница: 16 / 32

16
901302
SB M3x2.5
980210
P 2x10
DRIVE SHAFTS
#305323 US FOAM-SPEC - 50MM - STEEL
#305324 EU RUBBER-SPEC - 52MM - STEEL
#305325 ECS US FOAM-SPEC - 50MM - STEEL
#305326 EU RUBBER-SPEC - 52MM - ALU
#305327 ECS EU RUBBER-SPEC - 52MM - STEEL
#305328 US FOAM-SPEC - 50MM - ALU
05
4x
305326 (OPTION)
305340
940510
980210
902310
307455
307221
901302
302291
901304
902310
302663
901325
303032
305355
302663
307455
902310 901325
303032
307321
902306
302252
302346
302345
901304
303363
902314
307455
303353
305326 (OPTION)
305340
309319
THREAD
LOCK
GRAPHITE GREASE
(HUDY #106210)
TL
DO NOT
OVERTIGHTEN
302664
Drive shafts may be combined. For example, you may use the longer 52mm shafts with the optional
US Foam-Spec chassis, and the shorter 50mm shafts with the EU Rubber-Spec chassis. However, we
recommend using the drive shafts that are included in the kit since the drive shaft lengths have been
carefully chosen to optimize speed and ease of driving.
Longer drive shafts (52mm) make the car easier to drive because they give more traction and better
stability, mainly in chicanes. However, car will understeer more than with shorter (50mm) shafts
which give a lot of steering and impart aggression to the car. You may also combine different
lengths of shafts in front and rear (for example, using long shafts in the rear and short shafts in the
front) depending on track conditions.
Both left & right shafts should ALWAYS be the same length at one end of the car (front or rear).
305241
305355
! IMPORTANT
DO NOT use the plastic caps with
composite solid axle included in
the kits.
The new #305241 3.5mm plastic
caps are for use ONLY in REAR
with T2R PRO COMPOSITE ball diff
or with ALU ball diffs or the XRAY
Multi-Diff™.
1.5MM ALLEN
WRENCH
DO NOT
OVERTIGHTEN
305231
309319
52MM DRIVE SHAFTS
ARE INCLUDED IN KIT
BAG
5. FRONT & REAR TRANSMISSION
30 2252 COMPOSITE STEERING BLOCK - MEDIUM - RUBBER-SPEC
30 2253 COMPOSITE STEERING BLOCK - HARD - FOAM-SPEC (OPTION)
30 2291 STEEL STEERING BUSHING (2+2)
30 2345 COMPOSITE C-HUB FRONT BLOCK, RIGHT - 4° DEG.
30 2346 COMPOSITE C-HUB FRONT BLOCK, LEFT - 4° DEG.
30 2363 C-HUB RIGHT - 4° DEG. - MEDIUM - RUBBER-SPEC (OPTION)
30 2364 C-HUB LEFT - 4° DEG. - MEDIUM - RUBBER-SPEC (OPTION)
30 2373 C-HUB RIGHT - 4° DEG. - HARD - FOAM-SPEC (OPTION)
30 2374 C-HUB LEFT - 4° DEG. - HARD - FOAM-SPEC (OPTION)
30 2663 BALL JOINT 5 MM - OPEN (8)
30 2664 BALL JOINT 5 MM UNIDIRECTIONAL - OPEN (4)
30 3032 ALU QUICK ROLL-CENTER HOLDER™ 4.9MM (2)
30 3122 ALU SHIM 3x6x1.0MM (10) (OPTION)
30 3123 ALU SHIM 3x6x2.0MM (10) (OPTION)
30 3210 TURNBUCKLE L/R 25 MM - HUDY SPRING STEEL (2) (OPTION)
30 3352 UPRIGHT 0° OUTBOARD TOE-IN - MEDIUM - RUBBER-SPEC (OPTION)
30 3353 UPRIGHT 1° OUTBOARD TOE-IN - RIGHT - HARD - FOAM-SPEC
30 3363 UPRIGHT 1° OUTBOARD TOE-IN - LEFT - HARD - FOAM-SPEC
30 5231 DRIVE SHAFT COUPLING - HUDY SPRING STEEL
30 5241 DRIVE SHAFT REPLACEMENT PLASTIC CAP 3.5 MM (4)
30 5323 DRIVE SHAFT 50MM - HUDY SPRING STEEL (OPTION)
30 5324 DRIVE SHAFT 52MM - HUDY SPRING STEEL (OPTION)
30 5326 ALU DRIVE SHAFT SWISS 7075 T6 - HARD COATED - 52MM (OPTION)
30 5328 ALU DRIVE SHAFT SWISS 7075 T6 - HARD COATED - 50MM (OPTION)
30 5325 EQUALIZED CORNERING SPEED (ECS) DRIVE SHAFT 50MM (OPTION)
30 5327 EQUALIZED CORNERING SPEED (ECS) DRIVE SHAFT 52MM (OPTION)
30 5340 DRIVE AXLE - HUDY SPRING STEEL
30 5341 DRIVE AXLE - LIGHTWEIGHT - HUDY SPRING STEEL (OPTION)
30 5350 ALU WHEEL HUB (2) (OPTION)
30 5351 ALU WHEEL HUB - OFFSET “-0.75MM” (2) (OPTION)
30 5352 ALU WHEEL HUB - OFFSET “+0.75MM” (2) (OPTION)
30 5353 ALU WHEEL HUB - OFFSET “+1.5MM” (2) (OPTION)
30 5355 COMPOSITE WHEEL HUB (2)
30 7221 FRONT ARM PIVOT PIN (2)
30 7321 REAR ARM PIVOT PIN (2)
30 7455 PIVOT BALL 5.0 MM DOUBLE BEVEL SHOULDERS (10)
90 1302
HEX SCREW SB M3x2.5 (10)
90 1304 HEX SCREW SB M3x4 (10)
90 1325 HEX SCREW SB M3x25 (10)
90 2306 HEX SCREW SH M3x6 (10)
90 2310 HEX SCREW SH M3x10 (10)
90 2314 HEX SCREW SH M3x14 (10)
94 0510 HIGH-SPEED BALL-BEARING 5x10x4 RUBBER SEALED (2)
98 0210 PIN 2x10 (10)