background image

2

BEFORE YOU START

This is a high-competition, high-quality RC car intended for persons aged 16 

years and older with previous experience building and operating RC model 

racing cars. This is not a toy; it is a precision racing model. This model racing 

car  is  not  intended  for  use  by  beginners,  inexperienced  customers,  or  by 

children without direct supervision of a responsible, knowledgeable adult. 

If you do not fulfill these requirements, please return the kit in unused and 

unassembled form back to the shop where you have purchased it.

Before building and operating your XRAY, YOU MUST read through all of the 

operating  instructions  and  instruction  manual  and  fully  understand  them 

to  get  the  maximum  enjoyment  and  prevent  unnecessary  damage.  Read 

carefully and fully understand the instructions before beginning assembly.

Make sure you review this entire manual, download and use set-up book from 

the web, and examine all details carefully. If for some reason you decide this 

is not what you wanted or expected, do not continue any further. Your hobby 

dealer can not accept your kit for return or exchange after it has been partially 

or fully assembled.

Contents  of  the  box  may  differ  from  pictures.  In  line  with  our  policy  of 

continuous product development, the exact specifications of the kit may vary 

without prior notice. 

SAFETY PRECAUTIONS

WARNING: This product contains a chemical known to the state of California to 

cause cancer and birth defects or other reproductive harm.

CAUTION: CANCER HAZARD

Wash thoroughly after using. DO NOT use product while eating, drinking or using 

tobacco products. May cause chronic effects to gastrointestinal tract, CNS, kidneys, 

and blood. MAY CAUSE BIRTH DEFECTS.

When building, using and/or operating this model always wear protective glasses 

and gloves.

Take  appropriate  safety  precautions  prior  to  operating  this  model.  You  are 

responsible  for  this  model‘s  assembly  and  safe  operation!  Please  read  the 

instruction manual before building and operating this model and follow all safety 

precautions. Always keep the instruction manual at hand for quick reference, even 

after completing the assembly. Use only genuine and original authentic XRAY parts 

for  maximum  performance.  Using  any  third  party  parts  on  this  model  will  void 

guaranty immediately.

Improper  operation  may  cause  personal  and/or  property  damage.  XRAY  and 

its    distributors  have  no  control  over  damage  resulting  from  shipping,  improper 

construction, or improper usage. XRAY assumes and accepts no responsibility for 

personal  and/or  property  damages  resulting  from  the  use  of  improper  building 

materials, equipment and operations. By purchasing any item produced by XRAY, 

the  buyer  expressly  warrants  that  he/she  is  in  compliance  with  all  applicable 

federal,  state  and  local  laws  and  regulation  regarding  the  purchase,  ownership 

and use of the item. The buyer expressly agrees to indemnify and hold harmless 

XRAY for all claims resulting directly or indirectly from the purchase, ownership or 

use  of  the  product.  By  the  act  of  assembling  or  operating  this  product,  the  user 

accepts all resulting liability. If the buyer is not prepared to accept this liability, then 

he/she  should  return  this  kit  in  new,  unassembled,  and  unused  condition  to  the 

place of purchase.

      IMPORTANT NOTES – GENERAL

•  This product is not suitable for children under 16 years of age without the direct 

supervision of a responsible and knowledgeable adult.

•  Carefully read all manufacturers warnings and cautions for any parts used in the 

construction and use of your model.

•  Assemble this kit only in places away from the reach of very small children.

•  First-time builders and users should seek advice from people who have building 

experience in order to assemble the model correctly and to allow the model to 

reach its performance potential.

•  Exercise care when using tools and sharp instruments.

•  Take care when building, as some parts may have sharp edges.

•  Keep small parts out of reach of small children. Children must not be allowed to 

put any parts in their mouth, or pull vinyl bag over their head.

•  Read  and  follow  instructions  supplied  with  paints  and/or  cement,  if  used  (not 

included in kit).

•  Immediately after using your model, do NOT touch equipment on the model such 

as the motor and speed controller, because they generate high temperatures. 

You may seriously burn yourself seriously touching them.

•  Follow the operating instructions for the radio equipment at all times.

•  Do not put fingers or any objects inside rotating and moving parts, as this may 

cause damage or serious injury as your finger, hair, clothes, etc. may get caught.

•  Be sure that your operating frequency is clear before turning on or running your 

model, and never share the same frequency with somebody else at the same 

time. Ensure that others are aware of the operating frequency you are using and 

when you are using it.

•  Use a transmitter designed for ground use with RC cars. Make sure that no one 

else is using the same frequency as yours in your operating area. Using the same 

frequency at the same time, whether it is driving, flying or sailing, can cause loss 

of control of the RC model, resulting in a serious accident. 

•  Always turn on your transmitter before you turn on the receiver in the car. Always 

turn off the receiver before turning your transmitter off.

•  Keep the wheels of the model off the ground when checking the operation of the 

radio equipment.

•  Disconnect the battery pack before storing your model.

•  When learning to operate your model, go to an area that has no obstacles that 

can damage your model if your model suffers a collision.

•  Remove any sand, mud, dirt, grass or water before putting your model away.

•  If the model behaves strangely, immediately stop the model, check and clear the 

problem.

•  To prevent any serious personal injury and/or damage to property, be responsible 

when operating all remote controlled models.

•  The model car is not intended for use on public places and roads or areas where its 

operation can conflict with or disrupt pedestrian or vehicular traffic.

•  Because the model car is controlled by radio, it is subject to radio interference 

from many sources that are beyond your control. Since radio interference can 

cause momentary loss of control, always allow a safety margin in all directions 

around the model in order to prevent collisions.

•  Do not use your model:

  - Near real cars, animals, or people that are unaware that an RC car is being   

  driven.

  - In places where children and people gather

  - In residential districts and parks

  - In limited indoor spaces

  - In wet conditions

  - In the street

  -  In  areas  where  loud  noises  can  disturb  others,  such  as  hospitals  and  

   residential areas.

  -  At  night  or  anytime  your  line  of  sight  to  the  model  may  be  obstructed  or  

   impaired in any way.

To prevent any serious personal injury and/or damage to property, please be

responsible when operating all remote controlled models.

FAILURE TO FOLLOW THESE INSTRUCTIONS WILL BE CONSIDERED AS ABUSE AND/OR NEGLECT.

CUSTOMER SUPPORT 

XRAY Europe

K Výstavisku 6992

91101 Trenčín

Slovakia, EUROPE

Phone: +421-32-7401100

Fax: +421-32-7401109

Email: [email protected]

We have made every effort to make these instructions as easy to understand as 

possible.  However,  if  you  have  any  difficulties,  problems,  or  questions,  please 

do  not  hesitate  to  contact  the  XRAY  support  team  at  [email protected].  Also, 

please visit our Web site at www.teamxray.com to find the latest updates, set-up 

information, option parts, and many other goodies. We pride ourselves on taking 

excellent care of our customers.

You can join thousands of  XRAY fans and enthusiasts in our online community at:  

www.teamxray.com

XRAY USA

RC America, 2030 Century Center Blvd #15 

Irving, TX 75062 

USA

Phone: (214) 744-2400

Fax: (214) 744-2401

Email: [email protected]

   IMPORTANT NOTES – NITRO ENGINES

• Always  test  the  brakes  and  the  throttle  before  starting  your  engine  to  avoid 

losing control of the model.

• Make sure the air filter is clean and oiled. 

• Never  run  your  engine  without  an  air  filter.  Your  engine  can  be  seriously 

damaged if dirt and debris get inside the engine.

• For  proper  engine  break-in,  please  refer  to  the  manual  that  came  with  the 

engine.

• Do  not  run  near  open  flames  or  smoke  while  running  your  model  or  while 

handling fuel.

• Some parts will be hot after operation. Do not touch the exhaust or the engine 

until they have cooled. These parts may reach 275°F during operation!

Содержание NT1 2023





















































Отзывы: