Xray NT1 2023 Скачать руководство пользователя страница 47

Страница: 47 / 52

AFTER THE SHOCK IS ASSEMBLED YOU HAVE TO SET THE SHOCK REBOUND.

➊

Release the shock cap by 2-3 turns.

➋

Push the shock shaft fully up. For the first time the extra oil will release through the hole in the alu cap-nut.

➌

Tighten the shock cup. When tightening the shock cap, extra oil will again release through the hole in the alu

cap - nut. When tightening, the shock shaft will push out from the shock body.

RELEASE

2-3 turns

TIGHTEN

FULLY

REBOUND CHECK

It is very important to push the shock shaft into the shock body slowly otherwise air can come into the shock

body which would create bubles.

100% rebound - repeat step 2 and 3 two - three times

75%

rebound - repeat step 2 and 3 until the shock shaft will push out 75% of its length

50%

rebound - repeat step 2 and 3 until the shock shaft will push out 50% of its length

25%

rebound - repeat step 2 and 3 until the shock shaft will push out 25% of its length

rebound - repeat step 2 and 3 until the shock shaft will push out 0% of its length

If the shock shaft does not rebound enough, you will have to refill the shock with shock oil, and then repeat

the bleeding and rebound adjustment procedure.

REBOUND ADJUSTMENT

➊

➋

➌

SHOCK DAMPING

SPRING RATE SELECTION

C=4.0

LONG SPRINGS

C=4.5

LONG SPRINGS

STANDARD COLLARS

(#308331)

LOWER COLLARS

(#308335)

10. SHOCK ABSORBERS

50%

75%

100%

25%

NOTE ORIENTATION

(SHINY FINISH SIDE)

NOTE ORIENTATION

(SHINY FINISH SIDE)

SHOCK LENGTH ADJUSTMENT:

It is VERY important that all shocks are equal length.

Fully extend the shock absorber and measure the end-to-end length; we recommend using

digital calipers to give an accurate measurement. If a shock absorber is shorter or longer than

others, adjust the shock length by tightening or loosening the ball joint on the shock rod.

#308031-O or #308031-K

ALU XRAY SHOCK SPRING RETAINING COLLAR (4)

SPRINGS - SHORT

338182

PROGRESSIVE C=4.0-5.6 OPTION

338183

C=4.6

OPTION

338184

C=5.0

OPTION

338185

C=5.4

OPTION

338186

C=5.8

OPTION

338187

C=6.3

OPTION

SPRINGS - LONG

338281 PROGRESSIVE C=3.7-4.7 OPTION
338286 C=3.6

OPTION

338296 C=4.0

INCLUDED

338287 C=4.5

INCLUDED

338297 C=5.0

OPTION

338288 C=5.6

OPTION

Install the pivot balls with Professional

Multi Tool (HUDY #183011).

Содержание NT1 2023





















































Результаты поиска

Содержание NT1 2023

Отзывы:

Похожие инструкции для NT1 2023

Бренды по названию

Популярные бренды

Xray NT1 2023, Инструкция по эксплуатации

Результаты поиска

Содержание NT1 2023

Отзывы:

Похожие инструкции для NT1 2023

Бренды по названию

Популярные бренды