Inflatable jacuzzi – Instructions for use
|
3
conductor to the wire connector on the
terminal box that is provided for this
purpose.
16:
Risk of accidental drowning. Extreme
caution must be exercised to prevent
unauthorized access by children. To avoid
accidents, ensure that children cannot
use this spa unless they are supervised
at all times.
17:
During pregnancy, soaking in hot water
may cause damage to the unborn fetus.
Measure the water temperature before
using the spa, the water must not be
warmer than 38 degrees. Limit use to 10
minutes at a time.
18:
The use of alcohol, drugs, or medication
before or during the spa use may lead to
unconsciousness with the possibility of
drowning.
19:
Obese persons and persons with a
history of heart disease, low or high
blood pressure, circulatory system
problems, or diabetes should consult a
physician before use a spa.
20:
Persons using medication should
consult a physician before using a spa
since some medication may induce
drowsiness while other medication may
affect heart rate, blood pressure, and
circulation. The water in a spa should
never exceed 40°C (104°F). Water
temperature between 38°C (100°F) and
40°C (104°F) are considered safe for a
healthy adult. Lower water temperatures
are recommended for young children
and when spa use exceeds 10 minutes.
Since high water temperature has a
high potential for causing fatal damage
during the early months of pregnancy,
pregnant or possibly pregnant women
should limit spa water temperature to
38°C (100°F).
21:
To reduce the risk of injury, never use
water higher than 40°C (104°F) into the
spa directly.
22:
The use of alcohol, drugs, or medication
can greatly increase the risk of fatal
hyperthermia. Hyperthermia occurs
when the internal temperature of the
body reaches a level several degrees
above the normal body temperature
of 37°C (98.6°F). The symptoms of
hyperthermia include an increase in
the internal temperature of the body,
dizziness, lethargy, drowsiness, and
fainting, The effects of hyperthermia
include failure to perceive heat; failure
to recognize the need to exit the spa;
unawareness of impending hazard;
fatal damage in pregnant women;
physical inability to exit the spa; and
unconsciousness resulting in the danger
of drowning.
23:
Prolonged immersion in a spa may be
injurious to your health.
CAUTIONS
1:
To avoid damage to the pump, the spa
must never be operated unless the spa is
filled with water.
2:
Immediately leave spa if uncomfortable
or sleepy.
3:
Place only on surface that can withstand
the floor loading requirement of your spa.
4:
The spa should not be setup or left out in
temperature lower than 4°C (40°F).
5:
Never add water to chemicals. Always
adding chemicals to water may result in
a hazardous chemical spray.
6:
In order to avoid a hazard due to
inadvertent resetting of the thermal
cutout, this appliance must not be
supplied through an external switching
device, such as a timer, or connected to a
circuit that is regularly switched on and
off by the utility.
7:
This appliance is not intended for use
by persons (including children) with
reduced physical, sensory or mental
capabilities, or lack of experience and
knowledge, unless they have been given
supervision or instruction concerning use
of the appliance by a person responsible
for their safety.
8:
Children should be supervised to ensure
that they do not play with the appliance.
9:
The spa should not be setup or left out in
temperatures lower than 4°C (40°F).
After the spa being installed, please install the warning
label on where is at a distance within 1.5m to the spa,
thus the users in spa can see the warnings clearly. For the
first time users, please ask him/her read the warnings
carefully. If the warning label is damaged or missing,
please contact our spa service center to get a new one.
IMPORTANT:
Because of the combined weight of the
spa, water, and users, it is extremely important that the
base where the spa is installed is smooth, flat, level and
capable of uniformly supporting this weight for the entire
time the spa is installed. It is the responsibility of the spa
owner to assure the integrity of the site at all times.
- The spa can be used both indoors and outdoors. Only
use the product for its intended purpose.
- Ensure the ground is free of sharp objects.
- Ensure proper drainage of overflowed water.
- Ensure that the used socket is properly grounded and
easily accessible.
- Ensure you have enough space around the spa to
maintain it properly.
- Ensure proper drainage near the installation location so
you can drain the spa easily.
A. INDOORS INSTALLATION:
Be aware of special requirements if you install the spa indoors.
1. The floor must be able to withstand the capacity of the
spa. The floor should be a non-slip, level surface.
2. Proper drainage is essential for indoor spa installation.
When building a new room for the spa it is
recommended that a floor drain be installed.
3. Humidity is a natural side effect of spa installation. Determine
the effects of airborne moisture on exposed wood, paper,
etc. in the proposed location. To minimize these effects it is
best to provide plenty of ventilation to the selected area. An
architect can help determine if more ventilation is needed.
NOTE: Do not install the spa on carpet or other material
that can be damaged by moisture.
B. OUTDOORS INSTALLATION:
Spa owners must adhere to the local rules and regulations
that apply. Make sure you are aware of this.
1. No matter where you install the spa, it is important you
have a solid support foundation. If you are installing
the spa outdoors, ensure there are no sharp objects
that could damage it and that the location is level so
the spa sits stably and properly.
2. Do not install the spa on grass or sand, this can damage
the bottom of the spa. In addition, more dirt will end
up in the water.
3. During filling, emptying or when in use, water may spill out
of the spa. The spa should be installed near a ground drain.
4. Do not leave the spa’s surface exposed to direct
sunlight for long periods of time.
5. It is possible to install the spa outdoors when the
temperature is higher than 4°C (40°F). The temperature
in the spa, it’s circulation system and the tubes must be
higher than 4°C (40°F) and must not be frozen. Ensure
there is a temperature retaining mat under the spa to
prevent losing heat through the bottom of the spa.
ASSEMBLAGE
1. Unfold the spa from the packaging. Spread the spa and
cover. Make sure both are right side up.
2. Open the air outlet on the spa. Screw one end of the
inflation hose onto it.
3. Open the air valve on the spa. Connect the other end of
inflation hose into the valve.
4. Inflate the spa tub by pressing the “Jet” button.
