© XPAND, All Rights Reserved.
www.xpandvision.com
»
Add new device:
Opens a pop-up window which can be used to enter network parameters of a new device and add it to the
list of known devices.
»
Delete selected device:
Deletes the currently selected device from the list of known devices.
Device Network Settings
This section displays the connected modulator’s network settings as set on the device and also allows changing them. The fields and
controls listed below make this possible.
WARNING:
Modifying device network settings can make the device unreachable over the network if the wrong values are used. It is advised
you consult with your IT department before making any changes. New devices on the network may be blocked by the local network if
strong security is implemented. Your IT department must add the new device to their known devices list in order for them to be reachable
over the network.
»
Change Network Settings on Device button:
If a device is connected, pressing this button enables the user to modify
network settings on the modulator. Its IP address, network mask and default gateway can be changed. Once the button is
pressed, the “Device IP”, “Device Network Mask” and “Device Default Gateway” information becomes editable, the button is
transformed into a “Confirm New Network Settings” button and an additional “Abort” button is shown. When new values are
entered they are sent to the device by pressing the “Confirm New Network Settings” button. The process is aborted by pressing
the “Abort” button.
»
Device IP:
Displays the IP address of the currently connected device.
»
Device MAC:
Displays the MAC address of the currently connected device.
»
Device Network Mask:
Displays the network mask of the currently connected device.
»
Device Default Gateway:
Displays the default gateway of the currently connected device.
Device Information
This section displays general information about the connected modulator.
Device ID:
Displays the ID of detected device (e.g. XPS2A).
Firmware Version:
Used to identify the FW version loaded onto the modulator.
Current 3D Sync Frequency:
Reports whether a synchronization signal is detected on the modulator’s 3D sync GPIO input. Validity of the
signal and its frequency are reported. Whether a signal is valid or not is determined based on the currently set low and high frame sync
frequency settings. See parameters for
3D Sync Low Threshold Frequency
and
3D Sync High Threshold Frequency
described below.
Current Mode:
Reports whether the connected modulator is currently operating in 2D or 3D mode.
GPIO Logic Level:
Displays the logic level detected on GPIO input and the resulting mode of operation (e.g: Open Loop, 2D). Note that the
mode reported here may not be the same as the “Current Mode” described above if a control source other than GPIO is selected.
Device General Settings
This section displays and enables modification of general settings of the connected modulator.
3D Sync Signal Polarity:
Can be used to determine and change the interpretation of the incoming 3D sync synchronization signal’s levels.
“Normal” setting interprets a high level of the synchronization signal as corresponding to the left eye 3D image. If set to “Inverted”, the high
level is interpreted as corresponding to the right eye 3D image. So this parameter can be used to invert the left and right eye 3D images if
needed. This is usually done when 3D content seems “unnatural” and uncomfortable.
Motion Control Polarity:
Polarity of the motion control output signal. See section
Motion Control Output
for more information.
WARNING:
This parameter should not be used as a way of changing the modulator’s position!!! This is a global setting which should be con-
figured if needed when first installing the modulator on a motorized mount in front of the projector. See the
Installation
->
Motion Control
Setup Wizard
section of this manual for more information on how to properly set up and configure the modulator and motorized mount.
Global Delay:
Delay between the 3D sync edge and the start of the left/right-eye open intervals. Valid values are between 0 - 65535 µs.
Default value is 120 µs. If the value exceeds the current value of the frame synchronization signal period, the delay parameter is ignored.
To set global delay on the modulator, enter a new value and press the “Enter” key to confirm the change.
Содержание Passive 3D PolarizationModulator Gen2
Страница 19: ......
Страница 20: ...to be used on dark background to be used on light background...
