background image

 

USER MANUAL

 

Optima Rack 1-3K

 

___________________________________________________________________________________________________________________________________ 

(120217_EN) OPTIMA-RACK 1K-3K

 

  

19

 

 

11. ALARMS ON LCD 
 

ALARM Description 

ICON on LCD

Beep Alarm

Low battery 

 

1 / s

Overload: hi power consumption detected at 
UPS output. 

 

2 / s

Battery disconnected 

 

1 / s

Batteries overcharged 

 

1 / s

Input Cable failure 

1 / s

EPO enable 

 

1 / s

FAN failure 

 

1 / s

Over Temperature 

 

1 / s

Battery charger problem 

 

1 / s

Input out of range in bypass mode

 

1 / s

 
12. TROUBLESHOOTING TABLE 
Problem Description 

Probable Root Cause  

Suggested Action

 
* LCD does not show input voltage value 
 
* AC input failure alarm active  
(1 beep / 4s) however AC input source is 
OK 
 

Input power cord is not 
connected 

Check input power cord 
connection. 

Input power cord is connected 
into UPS outlet. 

Check input power cord 
connection. 

UPS cannot be powered on even AC 
input is OK. 
Beep alarm is active (1 beep/s) & LCD 
shows: 

  

 

EPO function is active. 
 

Re-establish emergency power 
off switch and set UPS in normal 
mode. 

 

USER MANUAL

 

Optima Rack 1-3K

 

___________________________________________________________________________________________________________________________________ 

(120217_EN) OPTIMA-RACK 1K-3K

 

  

20

 

 
 

UPS cannot be powered on even AC 
input is OK. 

ON push button is not been 
selected properly 

Push ON button during 2 
seconds or longer 

1 beep / s alarm is active and LCD 
shows: 

   

 

 

Input Line and Neutral are 
swapped 

Rotate UPS plug at wall socket 
to allow correct line-neutral 
connection. This suggestion is 
only valid for Schuko power plug 
type. 

1 beep / s alarm is active and LCD 
shows: 

  

Internal or external batteries are 
not properly connected 

Check battery connection. 

* Code 

27

*  Active: 

 

* Continuous beep 

Very high voltage at batteries or 
charger failure 

Batteries and charger must be 
inspected by qualified personnel 

* Code 

28

*  Active: 

 

* Continuous beep 

Very low voltage at batteries or 
charger failure 

Batteries and charger must be 
inspected by qualified personnel 

* Intermittent: 

 +

 

* 2 beeps per second. 

UPS overloaded

Disconnect devices from UPS 
outlets until solving overload 

* Intermittent: 

 +

 

* 2 beeps per second. 
* By-Pass activated 

UPS overloaded. UPS has 
changed to BYPASS mode to 
avoid internal damage.  

Disconnect devices from UPS 
outlets until solving overload 

After repetitive small overloads, 
UPS has changed to BYPASS 
mode. 

Disconnect devices from UPS 
outlets until solving overload. 
Then power off UPS and re-star 
again. 

* Code 

43

* Active:

 

* Continuous beep 

UPS has been automatically 
powered off because overload. 

Disconnect devices from UPS 
outlets until solving overload. 
Then power ON. 

* Active: 

 on LCD. 

* Continuous beep 

UPS has been automatically 
powered off because short 
circuit detected at output. 

Check short circuit problem in 
devices connected to UPS 

Содержание OPTIMA-RACK 1KVA














Отзывы: