manualshive.com logo in svg

XKL DarkStar DBA-L, Руководство пользователя

Поделиться
Скачать
XKL DarkStar DBA-L Скачать руководство пользователя страница 69

59

DarkStar User Guide

 4:  Troubleshooting

www.xkl.com

4.4     Recovery Mode

Recovery mode is a rare occurrence. You can manually enter recovery mode using the 

/recovery 

boot command switch. 

DXMOS enters recovery mode automatically at startup, if the 

startup-config 

file is detected to be unreadable, or 

contains corrupted data. 

All telnet and SSH access to the system is disabled in recovery mode. Only the console can be used to attempt recovery 
without dropping customer traffic. Recovery mode makes available a limited set of commands to load a remote backup copy 
of the configuration. Typically, the configuration is stored as a local file in

 /dxmos/config.dat

, but it may be acquired 

from remote sources by Boot during system startup. 

The commands available in recovery mode are:

You can recover a DarkStar system from a configuration file stored on a remote server. The system must be physically cabled to 
a live management network in order for this process to work. If the remote configuration file matches the running configu-
ration, customer traffic on the DarkStar system will not be interrupted.

NOTE

XKL strongly encourages you to maintain current copies of your configuration using the 

write 

memory

 and 

write network

 commands whenever configuration changes are made. 

The following example shows system recovery using the boot command 

/recovery 

switch. Modify the example with 

installation-specific values to implement recovery. 

TABLE 4.5 

Recovery Mode Commands

Command

Description

configure

Enter configure mode to configure an Ethernet interface in advance of 
issuing a 

configure network

 command.

configure network 
<IPaddress> <FilePath>

Download a remote configuration backup when a management Ethernet 
interface is already configured.

continue

In cases where flash memory is unreadable or corrupt, and a backup 
configuration is unavailable, continue DXMOS startup without a configu-
ration. NOTE: continuing system startup without a configuration may 
cause loss of customer traffic, and will leave management interfaces 
unconfigured. Configuration settings must then be applied using 
manually issued commands at the console.

verbosity

Controls warning message levels.

drop-to-boot

Revert to the system boot loader to access Boot facilities.

ping/ping6

Test IPv4/IPv6 connectivity.

reload

Reload all system software and gateware from flash memory.

show

Display information about the recovery mode system configurations.

Содержание DarkStar DBA-L









































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды