Xilinx ZCU102 Скачать руководство пользователя страница 22

Страница: 22 / 137

ZCU102 Evaluation Board User Guide

www.xilinx.com

UG1182 (v1.2) March 20, 2017

Chapter 3:

Board Component Descriptions

The Zynq Ult MPSoC PS block has three major processing units:

Cortex-A53 application processing unit (APU)-ARM v8 architecture-based 64-bit

quad-core multiprocessing CPU.

Cortex-R5 real-time processing unit (RPU)-ARM v7 architecture-based 32-bit dual

real-time processing unit with dedicated tightly coupled memory (TCM).

Mali-400 graphics processing unit (GPU)-graphics processing unit with pixel and

geometry processor and 64 KB L2 cache.

The Zynq Ult MPSoC PS has four high-speed serial I/O (HSSIO) interfaces

supporting the following protocols:

Integrated block for PCI Express® interface-PCIe™ base specification version 2.1

compliant.

SATA 3.1 specification compliant interface.

DisplayPort interface-implements a DisplayPort source-only interface with video

resolution up to 4K x 2K-30 (300 MHz pixel rate).

USB 3.0 interface-compliant to USB 3.0 specification implementing a 5 Gb/s line

rate.

Serial GMII interface-supports a 1 Gb/s SGMII interface.

The PS and PL can be coupled with multiple interfaces and other signals to effectively

integrate user-created hardware accelerators and other functions in the PL logic that are

accessible to the processors. They can also access memory resources in the processing

system. The PS I/O peripherals, including the static/flash memory interfaces share a

multiplexed I/O (MIO) of up to 78 MIO pins. Zynq Ult MPSoCs can also use the I/O

in the PL domain for many of the PS I/O peripherals. This is done through an extended

multiplexed I/O interface (EMIO).and boots at power-up or reset.

For additional information on Zynq Ult MPSoC devices, see the

UltraScale

Architecture and Product Overview

(DS890)

[Ref 1]

, and the

Zynq Ult MPSoC

Technical Reference Manual

(UG1085)

[Ref 2]

for more information about Zynq Ult

MPSoC configuration options.

Send Feedback

Содержание ZCU102










































































































































Результаты поиска

Содержание ZCU102

Отзывы:

Бренды по названию

Популярные бренды

Xilinx ZCU102, Руководство пользователя

Результаты поиска

Содержание ZCU102

Отзывы:

Бренды по названию

Популярные бренды