Xilinx Vivado MIPI CSI-2 страница 83 Скачать руководство пользователя

Страница: 83 / 90

MIPI CSI-2 RX Subsystem v4.0

PG232 July 02, 2019

www.xilinx.com

Appendix B:

Debugging

Hardware Debug

Hardware issues can range from link bring-up to problems seen after hours of testing. This

section provides debug steps for common issues. The Vivado debug feature is a valuable

resource to use in hardware debug. The signal names mentioned in the following individual

sections can be probed using the debug feature for debugging the specific problems.

General Checks

• Ensure MIPI DPHY and MIPI CSI-2 RX Controller cores are in the enable state by reading

the registers.

• Ensure Incorrect Lane Configuration is not set in the MIPI CSI-2 RX Controller Interrupt

Status register.

• Ensure line buffer full condition is not set in the MIPI CSI-2 RX Controller Interrupt

Status register. Core setting this bit implies that the input data rate is higher than the

output data rate. Consider either decreasing input data rate (DPHY Line rate) or

increase output data rate (Select appropriate output pixel per Clock: Single, Dual,

Quad).

• Ensure that the PULLUP constraints required for the AXI IIC core pins are set at the

system-level XDC when the AXI IIC core is enabled. (See the

AXI IIC Bus Interface v2.0

LogiCORE IP Product Guide

(PG090)

[Ref 5]

for more information).

• Following MIPI CSI-2 RX Controller registers can be monitored to confirm reception of

data packets

Packet count in Core Status register

Data type and Byte count in Image Information registers

Frame received bit in Interrupt Status register

• No packets received by MIPI CSI-2 Subsystem

Possible causes:
- No packets received at MIPI DPHY level itself
- Frame end packets not received or not passed the ECC checks at MIPI CSI-2 RX

Subsystem level

Debug instructions:
- Verify MIPI DPHY packet count registers. If the packet counts at MIPI DPHY level

are not getting reported, debug connections/paths from source to MIPI DPHY

Input

Send Feedback

Содержание Vivado MIPI CSI-2



























































































Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Похожие инструкции для Vivado MIPI CSI-2

Бренды по названию

Популярные бренды

Xilinx Vivado MIPI CSI-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Похожие инструкции для Vivado MIPI CSI-2

Бренды по названию

Популярные бренды