Xilinx Vivado MIPI CSI-2 Скачать руководство пользователя страница 54

Страница: 54 / 90

MIPI CSI-2 RX Subsystem v4.0

PG232 July 02, 2019

www.xilinx.com

Chapter 4:

Design Flow Steps

Pixel Format

: Select Data Type (pixel format) as per the CSI-2 protocol (RAW6, RAW7,

RAW8, RAW10, RAW12, RAW14, RGB888, RGB666, RGB565, RGB555, RGB444, YUV422_8bit).

Serial Data Lanes

: Select the maximum number of D-PHY lanes for this subsystem instance.

Values are 1, 2, 3, or 4.

Enable AXI IIC

: Select to add the AXI IIC core (for CCI support).

Include Video Format Bridge (VFB)

: Option to include or exclude the Video Format Bridge

core in the subsystem.

Support CSI Spec V2_0

: Select to enable CSI V2.0 features (RAW16, RAW20 support and

VCX feature support).

Support VCX Feature

: Option to include or exclude VCX feature.

Line Rate (Mb/s)

: Select the line rate for the MIPI D-PHY core. Value in the range, 80 to

2500 Mb/s based on the device selected. Vivado IDE automatically limits the line rates

based on the device selected. For details about family/device specific line rate support refer

UltraScale Architecture SelectIO Resources User Guide

(UG571)

[Ref 16]

. See the respective 7

Series family device data sheet for details on the upper line rate limits.

D-PHY Register Interface

: Select to enable the register interface for the MIPI D-PHY core.

Enable Deskew Detection

: Select to enable Deskew sequence detection and centre

alignment of clock and data lanes in MIPI D-PHY.

Note:

Applicable only for line rates above 1500 Mb/s

Calibration Mode:

Select the calibration for 7 Series MIPI D-PHY RX Subsystem. Values are

None, Fixed, or Auto. When set to None, the

Calibration Mode

does not add IDELAY2

primitive. Fixed as

Calibration Mode

will set IDELAYE2 TAP value set in

IDELAY Tap Value

Auto as

Calibration Mode

will add IDELAYE2 primitive and tap value will be configured by

D-PHY RX IP based on received traffic and calibration algorithm.

IDELAY Tap Value:

Select the IDELAY TAP value used for calibration in Fixed mode. Value in

the range, 1 to 31.

Include IDELAYCTRL in core:

Select to include IDELAYCTRL in core. Only available in FIXED

and AUTO calibration modes. For multiple MIPI CSI-2 Rx IP cores that are sharing single IO

bank, select

Include IDELAYCTRL

option in the IP for the auto calibration mode. Only one

IDELAYCTRL

is available per a single clock region. If multiple MIPI CSI-2 RX cores exist in

single clock region, select this option for only one MIPI CSI-2 RX IP core. For the rest of MIPI

CSI-2 RX cores, this option should be unselected.

Note:

This option is applicable only for 7 Series MIPI CSI-2 RX IP configurations.

Send Feedback

Содержание Vivado MIPI CSI-2



























































































Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Бренды по названию

Популярные бренды

Xilinx Vivado MIPI CSI-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Бренды по названию

Популярные бренды