Xilinx Vivado MIPI CSI-2 страница 6 Скачать руководство пользователя

Страница: 6 / 90

MIPI CSI-2 RX Subsystem v4.0

PG232 July 02, 2019

www.xilinx.com

Chapter 1:

Overview

Sub-Core Details

MIPI D-PHY

The MIPI D-PHY IP core implements a D-PHY RX interface and provides PHY protocol layer

support compatible with the CSI-2 RX interface. The MIPI D-PHY IP core also supports the

deskew pattern detection for line rates >1.5 Gb/s. See the

MIPI D-PHY LogiCORE IP Product

Guide (

PG202

)

[Ref 3]

for details. MIPI D-PHY implementation differs for the Ult

devices and the 7 Series devices with respect to I/O.

For Ult devices, the Vivado IDE provides a

Pin Assignment Tab

to select the

required I/O. However, for the 7 series devices the clock capable I/O should be selected

manually. In addition, the 7 series devices do not have a native MIPI IOB support. You will

have to target either HR bank I/O or HP bank I/O for the MIPI IP implementation. For more

information on MIPI IOB compliant solution and guidance, refer

D-PHY Solutions

(XAPP894)

[Ref 15]

MIPI CSI-2 RX Controller

The MIPI CSI-2 RX Controller core consists of multiple layers defined in the MIPI CSI-2 RX

1.1 specification, such as the lane management layer, low level protocol and byte to pixel

conversion.

The MIPI CSI-2 RX Controller core receives 8-bit data per lane, with support for up to 4

lanes, from the MIPI D-PHY core through the PPI. As shown in

Figure 1-1

the byte data

received on the PPI is then processed by the low level protocol module to extract the real

image information. The final extracted image is made available to the user/processor

interface using the AXI4-Stream protocol. The lane management block always operates on

32-bit data received from PPI irrespective number of lanes.

Send Feedback

Содержание Vivado MIPI CSI-2



























































































Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Похожие инструкции для Vivado MIPI CSI-2

Бренды по названию

Популярные бренды

Xilinx Vivado MIPI CSI-2, Руководство по эксплуатации продукта

Результаты поиска

Содержание Vivado MIPI CSI-2

Отзывы:

Похожие инструкции для Vivado MIPI CSI-2

Бренды по названию

Популярные бренды