background image

MLP2 User Manual

2

IMPORTANT SAFETY INSTRUCTIONS

In using the present appliance, please keep the following safety regulations in order to prevent
any hazard or material damage.

1.Safety Precautions

1) Be sure to use the specified battery and power charger provided by our company,

connection to an improper power charger may cause fire, explosion or damage to the
printer.

2) Don’t put the battery into fire or water, don’t disassemble or modify the battery, don’t be

short circuit, otherwise may result in injury or fire or even explosion.

3) If the printer would not be used for a long time, be sure to take off the battery, otherwise

the battery may leak liquid which is corrosive, if improper operation causes battery leak,
and the liquid is spattered on the skin or clothes, please wash it with water, if spattered into
the eyes, please rinse them with water thoroughly and see a doctor.

4) Please do not open the paper case cover when it is printing or just when printing is over, do

not touch the print head with hand or body, overheat may cause scald.

2. Operation Precautions

1) Water or other liquid should not spill into the printer, also the printer should not be expose

to the rain, or else may cause printer damage.

2) Please do not open the paper case cover when it is printing, otherwise the printer may

work improperly.

3) If print with serial interface, should not unplug the interface cable in the course of printing,

or else some printing data may be lost.

4) When print with Bluetooth interface, the communication distance should be within 10

meters, otherwise the printer doesn’t print or prints rubbish codes.

5) Too high (40

) or too low (0

) temperature and too high (85

) or too low (20

) relative

humidity both effect the print quality.

6) The print paper in poor quality or stored for too long time also may reduce the print quality

even damage the printer.

3.Storage Precautions

1) The printer should be placed in such an environment that the temperature is between

-20

and 70

, and the relative humidity is between 5% and 95%.

Содержание MLP2


























Отзывы: