Xerox WIDE FORMAT 721P Скачать руководство пользователя страница 8 | Manualshive

Страница: 8 / 72

background image

INTRODUCTION

viii

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

Japan

This is a Class A product based on the standard of the Voluntary
Control Council for Interference by Information Technology
Equipment (VCCI). If this equipment is used in a domestic
environment, radio disturbance may arise. When such trouble
occurs, the user may be required to take corrective actions.

Changes or modifications to this equipment not specifically
approved by Fuji

XEROX

Limited may void the user’s authority to

operate this equipment.

Shielded cables must be used with this equipment to maintain
compliance with the Voluntary Control Council for Interference by
Information Technology Equipment regulations.

USA

This equipment has been tested and found to comply with the
limits for a Class A digital device, pursuant to Part 15 of the FCC
Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a
commercial environment. This equipment generates, uses, and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruction manual, may cause harmful
interference to radio communications. Operation of this equipment
in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own
expense.

Changes or modifications to this equipment not specifically
approved by the

XEROX

Corporation may void the user’s authority

to operate this equipment.

Shielded cables must be used with this equipment to maintain
compliance with FCC regulations.

«
...
6
7
8
9
10
...
»

Содержание WIDE FORMAT 721P









































































Отзывы:

Нет отзывов

Похожие инструкции для WIDE FORMAT 721P

Бренд: Xerox Страницы: 25

Бренд: Datecs Страницы: 73

Бренд: Datamax Страницы: 12

E-Class Mark II

Бренд: Datamax Страницы: 40

Бренд: Datamax Страницы: 46

Бренд: Canon Страницы: 198

Бренд: Xerox Страницы: 200

WorkCentre Pro 32

Бренд: Xerox Страницы: 14

Бренд: Olympus Страницы: 16

Бренд: EFI Страницы: 4

Бренд: ICT Страницы: 34

Бренд: Lexmark Страницы: 221

Бренд: Oki Страницы: 309

Бренд: A&D Страницы: 102

WorkCentre 5687 Series

Бренд: Xerox Страницы: 2320

VersaaLink B600

Бренд: Xerox Страницы: 170

Artisan 810 Series

Бренд: Epson Страницы: 36

Бренд: Epson Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды