Xerox WIDE FORMAT 721P Скачать руководство пользователя страница 54

Страница: 54 / 72

PROBLEM SOLVING

XEROX WIDE FORMAT 721P PRINTER OPERATOR MANUAL

Door Open Errors (U-XX)

When the printer experiences a door open error, the following
occurs:

The Door Open Indicator flashes orange.

An error code “U-XX” flashes.

For codes U-04 or U-14, the location of the open door is also

shown by PF or EXIT.

Error Code

Cause

Treatment

U-01

The Upper Drawer is open.

Open and close the Upper Drawer.

U-02

The Middle Drawer is open.

Open and close the Middle Drawer.

U-03

The Lower Drawer is open.

Open and close the Lower Drawer.

U-04

The Inner Transport is open.

Close the Inner Transport.

Note: When you turn the latch, confirm
that it is locked.

U-06

Left Door is open.

Close the Left Door.

U-11

Manual Bypass Shelf is open.

Open and close the Manual Bypass Shelf.

U 10

A interlock is open.

Reset the Manual Bypass Shelf, Right
Door, Top Rear Cover, Exit Cover

U-12

Right Door is open.

Close the Right Side Door.

U-13

Top Rear Cover is open.

Close the Top Rear Cover.

U-14

Exit Cover is open.

Close the Exit Cover.

Thumping Noise in Standby

After 30 minutes of no use, the printer will reset the developer
motor and enter an idle state. A loud “thump” noise will be heard
as the motor resets. This is normal.

Exp-Clean

Wire-Clean

Paper Deck

1 2 3 4

Select

Cut

Exit

Copy Density

Enter

Online

Door Open Indicator

PF and Exit

Error Cord

Error Code

Содержание WIDE FORMAT 721P









































































Результаты поиска

Содержание WIDE FORMAT 721P

Отзывы:

Похожие инструкции для WIDE FORMAT 721P

Бренды по названию

Популярные бренды

Xerox WIDE FORMAT 721P, Руководство оператора

Результаты поиска

Содержание WIDE FORMAT 721P

Отзывы:

Похожие инструкции для WIDE FORMAT 721P

Бренды по названию

Популярные бренды