Xerox DocuPrint 65 Скачать руководство пользователя страница 48 | Manualshive

Страница: 48 / 74

Xerox DocuPrint 65 Скачать руководство пользователя страница 48

Maintenance

Operator Guide

2-8

DocuTech 65/DocuPrint 65

CAUTION

When the power on/standby switch is in stand-by and the AC power cord
remains connected to a power receptacle, AC voltage is present in the power
supply.

10. If the equipment will be serviced or moved, disconnect the AC power cord

from the AC receptacle.

Emergency power-off procedures

An emergency power-off procedure may be used when the power must be
switched off immediately.

CAUTION

The controller emergency power off procedure may corrupt the DocuSP
software. This method should only be used in an emergency.

Controller Power-

Off

To power off the system in an emergency use any of the following methods:

•

Switch off the controller power switch on the front of the controller.

•

On the DocuSP Print Services, the System menu, select the option for
Immediate Shutdown.

•

Pull the controller power cord from its receptacle.

Printer power-off

To power off the printer in an emergency use any of the following methods:

•

Press the red button on the printer.

•

Pull the printer power cord from the power receptacle.

An emergency power off of the printer will not corrupt the DocuSP system
software. However, you will need to enter Reset at the OK prompt if the
controller displays the OK prompt.

Controller or

Printer Emergency

Conditions

For the printer or the controller, if any of the following conditions occur,
disconnect the power cable from the power socket immediately and contact
an authorized Xerox Service Representative to correct the problem

•

The equipment emits unusual odors, or makes unusual noises.

•

The power cable is damaged or frayed.

•

A wall panel circuit breaker, fuse, or other safety device has been tripped.

•

Liquid is spilled into the equipment.

•

The equipment is exposed to water damage or flood.

•

Any part of the equipment is physically damaged.

«
...
46
47
48
49
50
...
»

Содержание DocuPrint 65











































































Отзывы:

Нет отзывов