Xero88 CHILLI DIMMER Скачать руководство пользователя | Manualshive

Страница: 3 / 30

background image

Introduction

Chilli Dimmer 73-853-00 Issue 8

Page 3 of 30

Introduction

Dimmer

Version

Breakers

Residual Current

Device (RCD)

Mains Supply

Temperature

Monitoring

Pro 4 x 10

Neutral Disconnect

-

Single Phase Only

-

Pro 4 x 10 HF

Neutral Disconnect

-

Single Phase Only

-

12 x 10

Single Pole

Option

Three Phase (see note)

Yes

Pro 12 x 10

Neutral Disconnect

Option

Three Phase (see note)

Yes

Pro 12 x 10 HF

Neutral Disconnect

-

Three Phase

-

12 x 16

Single Pole

Option

Three Phase (see note)

Yes

Pro 12 x 16

Neutral Disconnect

Option

Three Phase (see note)

Yes

24 x 10

Single Pole

Option

Three Phase (see note)

Yes

Pro 24 x 10

Neutral Disconnect

Option

Three Phase (see note)

Yes

Pro 24 x 16

Neutral Disconnect

-

Three Phase (see note)

Yes

Pro 6 x 25

Neutral Disconnect

Option

Three Phase

Yes

Table 1: Chilli Dimmer Variants

Note - Single Phase Conversion

Additional information detailing how to convert these dimmers for single phase operation is given in a separate
document TU7806 available for download from the Zero 88 website.

This Manual

This  manual  describes  the  operation  of  the  Chilli
Dimmer. It is written for dimmers with the new white
backlit  user  interface  (see  figure  1  -  1)  running
version  7.00  firmware  onwards.  For  older  dimmers
with the green backlit user interface, please refer to
the Issue 7 manual supplied with the dimmer.

This chapter contains a general overview of the unit
followed by a brief description of the front panel
controls and displays.

The  Installation  chapter  provides  information  on
installing  the  dimmer  and  connecting  up  the  mains,
loads, DMX, Chilli network and alarm input.

The User Interface chapter describes all the various
functions of the dimmer which can be set up and
operated via the front panel controls.

The manual concludes with a chapter on the
technical specification of the dimmer.

Conventions

Throughout this manual the following conventions
are used.

References to front panel controls, appear in capital
letters, for example:

ENT key, ESC key.

References to the LCD screen on the control panel
are shown as follows:

DMX: 1

Temp: OK

References to fields which appear on the LCD
screen are shown in italics, for example:

Manual Control, Set Chan Level etc.

«
1
2
3
4
5
...
»

Содержание CHILLI DIMMER































Отзывы:

Нет отзывов

Похожие инструкции для CHILLI DIMMER

Бренд: Makita Страницы: 9

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 48

Бренд: Makita Страницы: 20

Бренд: Makita Страницы: 56

Бренд: Makita Страницы: 18

Бренд: Makita Страницы: 26

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 16

Бренд: Makita Страницы: 9

4050, 4850, 5550, 6350

Бренд: Makita Страницы: 7

Бренд: Makita Страницы: 2

Бренд: Makita Страницы: 232

Бренд: Makita Страницы: 4

Бренд: BaByliss for MEN Страницы: 12

Бренд: Echo Страницы: 34

Sunjoe 24V-X2-24HT-CT-RM

Бренд: SNOWJOE Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды