Xero88 CHILLI DIMMER Скачать руководство пользователя

Страница: 14 / 30

Installation

Chilli Dimmer 73-853-00 Issue 8

Page 14 of 30

DMX Connection

DMX input is connected through a
4-way screw terminal block located
on the control PCB (Figure 2-12).

loop

through

another

dimmer,  simply  connect  both  sets
of  wires  into  the  same  terminal
block.

The terminals to be used are
labelled RS485-, RS485+ and 0V.

The connector is in 2 parts and the
screw  terminal  part  may  be
removed  from  the  PCB  to  ease
making the connections.

If  removed  for  wiring,  ensure  that
the  orientation  is  correct  when
replacing the connector.

A 3-way DIP switch is located
above the DMX terminations.

Switch 1

TRIAC Units - Undefined.

HF Units - Ballast Controller Mode:

0 - 10V Analogue - switch to left

DSI - switch to right.

Switch 2

Fail to ON - switch to left;

Fail to OFF - switch to right

Switch 3

DMX terminator OUT - switch to left;

DMX terminator IN - switch to right

Alarm Input Connection

The  Alarm  Input  is  connected
through  a  4-way  screw  terminal
block  located  on  the  control  PCB
(Figure 2-13).

The  terminals  to  be  used  for  the
Alarm  Input  are  labelled  0V  and
AL.

Any  connection  to  the  Alarm  Input
must be volt free and have a cable
length  of  less  than  50  metres.
Cabling  for  this  input  should  be
segregated from power wiring.

The connector is in 2 parts and the
screw  terminal  part  may  be
removed  from  the  PCB  to  ease
making the connections.

If  removed  for  wiring,  ensure  that
the  orientation  is  correct  when
replacing the connector.

Figure 2 - 12: DMX Connections

Figure 2 - 13: Alarm Input Connections

Содержание CHILLI DIMMER































Результаты поиска

Содержание CHILLI DIMMER

Отзывы:

Похожие инструкции для CHILLI DIMMER

Бренды по названию

Популярные бренды

Xero88 CHILLI DIMMER, Руководство по эксплуатации

Результаты поиска

Содержание CHILLI DIMMER

Отзывы:

Похожие инструкции для CHILLI DIMMER

Бренды по названию

Популярные бренды