background image

76

Evolve User Manual V1.0 by XDynamics Limited

Safety 

RF Radiation

RF radiation exposure statement The Product complies with FCC RF radiation exposure limits set for an 
uncontrolled environment. Use of other unapproved accessories may not ensure compliance with FCC 
RF exposure guidelines. 

FCC Part 15 - This equipment has been tested and found to comply with the requirements for a 
Class B digital device under Part 15 of the Federal Communications Commission (FCC) rules. These 
requirements are intended to provide reasonable protection against harmful interference in a residential 
installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed 
and used in accordance with the instructions, may cause harmful interference to radio communications. 
However, there is no guarantee that interference will not occur in a particular installation. 

This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: 
(1) This device may not cause harmful interference

(2) This device must accept any interference received, including interference that may cause undesired 
operation. 

To ensure safety of users, the FCC has established criteria for the amount of radio frequency energy that 
can be safely absorbed by a user or bystander according to the intended usage of the product. This 
product has been tested and found to comply with the FCC criteria. 

NEED TO VERIFY THIS SECTION WITH SPECIALIST

Содержание EVOLVE
















































































Отзывы: