XciteRC X-PERT X90T, Руководство пользователя

Страница: 28 / 52

28 X-pert Charger X90T
EN
End of charging
·
Data View Mode
M11 M12 M13 M14
M15 M16 M17 M18
BACK SAVE
BACK START
LiPo CHG Con fi rm
-Connect -
Input Vol ... OK
Mainport ... OK
Bala Port ... OK
TYPE
LiPo
CELLS
6S
CURR
2.2A
Set Charge Current
2.2 A
SAVE BACK START
TYPE
LiPo
CELLS
6S
CURR
2.2A
Set Battery type
LiPo
SAVE BACK START
TYPE
LiPo
CELLS
6S
CURR
2.2A
Number Of Cells
6 (s)
SAVE BACK START
GRAPH DATA STOP CELL
Input Volt 12.51V
End Volt. 25.20V
CAPA Cut-Off 10.0Ah
Safety Timer 240min
Temp.Cut-Off 60
℃
:
:
:
:
:
GRAPH DATA STOP CELL
Voltage 24.76V
Current 2.16A
Capacity 7mAh
Int Temp. 33
℃
Ext Temp. 29
℃
:
:
:
:
:
GRAPH DATA STOP CYCLE
C1 : 9 D1 : 0mAh
C2 : 0 D2 : 0mAh
C3 : 0 D3 : 0mAh
C4 : 0 D4 : 0mAh
C5 : 0 D5 : 0mAh
GRAPH DATA STOP CELL
1) 4.124
2) 4.130
3) 4.113
4) 4.122
5) 4.135
6) 4.117
GRAPH STOP CELL
LiPo BCHG 6S 00:00:45 24.75V 00:01:41
BACK
Nixx Cycle record
LiPo BCHG 6S 00:00:45
LiPo BCHG 6S 00:00:20
Select
battery type (TYPE)
and
number of cells (CELLS)
Set number of cells (CELLS) with
the arrow keys
increase value
decrease value
Set
charging current
(CURR) with the arrow keys
increase value
decrease value
Note: the charger will set the charge current
according to a rate of 1C automatically when
you set the capacity of the battery pack. If the
battery pack allows you to charge with a
higher rate, you can set the current CURR
higher.
WARNING: check the battery sticker to
make sure the battery is designed for a
higher charging current -
fire hazard!
SAVE your settings.
When charging this battery
again, you may select the
battery memory on the
Main screen.
Please see chapter
Charging process.
or
press START. The battery
will be charged without saving
the charging parameters.
Charging monitor
Voltage:
Current:
Capacity:
Int. Temp.:
Ext. Temp.:
current battery voltage
current charging current
charging capacity
Charger internal temperature
is an external temperature sensor connected, the
temperature is shown here
DATA monitor
Current input voltage
Battery cut-off voltage
Max. capacity
Safety timer
Battery cut-off temperature
GRAPH
graphical display of the
charging voltage
Press BACK to go back to the
charging monitor
CELL
graphical and numerical display
of the cell voltages
NiXX CYCLE
numerical display of the cycle
data
(NiXX mode only)
End of charging
• If the battery is fully charged, FULL appears in the display, as well as an acoustic signal sounds for about
10 seconds.
• NOTE: if the charging process is terminated by safety timer, the display will show STOP . Check the
charging parameters and start the charging process again if necessary.
• When charging is complete, the battery can be disconnected from the charger. If the charger is no longer
needed, it should be disconnected from the power supply.
Data View Mode - single cell voltage/internal resistance
here you can check the single cell voltage and internal resistance of the connected battery pack.
STOP
1) 4.108
2) 4.097
3) 4.103
4) 4.104
5) 4.102
6) 4.108
00.00.09
VOL LiPo BACK BALA
1) 08m
Ω
2) 15m
Ω
3) 06m
Ω
4) 09m
Ω
5) 14m
Ω
6) 04m
Ω
IR LiPo BACK BALA
1) 4.110
2) 4.097
3) 4.103
4) 4.105
5) 4.103
6) 4.109
LiPo
VOL
BALA
Select battery type
(LiPo / LiIo / LiFe)
Select single cell voltage
VOL or internal resistance
IR
.
The balancer function BALA
is recommended for an
unbalanced or old battery.
Press BALA to start.