XCHARGE NZS Series Скачать руководство пользователя страница 8

Страница: 8 / 62

1.4 Signs

These signs below are also used on the nameplate of NZS:

Signs

Description

Earthing

Connect an earth terminal to earth

General Warning Sign

Identify a hazard that may result in damage to the
operator, machinery, other equipment and / or
contamination.

Electricity Hazard

Warning of electrical voltage

Crushing of Hands

Touching the device may result in hand injuries

No access for people with active
implanted cardiac devices

Signs

Description

Pay attention to documentation

Observe all documentation supplied with the product.

WEEE Symbol

Do not dispose of the product with household waste.
Please observe the applicable disposal regulations at
the place of installation for electronic waste.

CE-symbol

Содержание NZS Series































































Результаты поиска

Содержание NZS Series

Отзывы:

Похожие инструкции для NZS Series

Бренды по названию

Популярные бренды

XCHARGE NZS Series, Инструкция по установке и эксплуатации

Результаты поиска

Содержание NZS Series

Отзывы:

Похожие инструкции для NZS Series

Бренды по названию

Популярные бренды