background image

5

Fire hazard.  

Plasma cutting on closed containers, such as tanks,drums, or pipes, can cause 

them to explode. Flying sparks from the welding arc, hot work piece, and hot equipment can 

cause fires and burns. Accidental contact of electrode to metal objects can cause sparks, ex

-

plosion, overheating, or fire. Check and be sure the area is safe before doing any cutting.

 

   • 

The cutting sparks may cause fire, therefore 

   

remove any flammable materials well away from the working

 

  area. Cover flammable materials and containers with approved covers if unable to be moved from the

 

  welding area. 
   •  Do not Plasma Cut closed containers such as tanks, drums, or pipes, unless they areproperly prepared  
  according to the required Safety Standards to 

insure that flammable or toxic vapors and substances are

 

  totally removed, these can cause an explosion even though the vessel has been “cleaned”. Vent hollow

 

  castings or containers before heating, cutting or welding. They may explode. 
    •

  Do not cut where the atmosphere may contain flammable dust, gas, or liquid vapours (such as petrol)

 

• 

Have a fire extinguisher nearby and know how to use it. 

Be alert that cutting sparks and hot materials 

  from cutting can easily go through small cracks and openings to adjacent areas.  Be aware that cutting 

  on a ceiling, floor, bulkhead, or partition can cause fire on the hidden side.

 

 

Gas Cylinders. 

Do not cut in the vicinity of pressurised gas cylinders or in the presence of 

explosive dust, gases or fumes. Gas cylinders contain gas under high pressure. If damaged, 
a cylinder can explode. Because gas cylinders are normally part of the welding process, be 
sure to treat them carefully. CYLINDERS can explode if damaged. 

   •

 Protect gas cylinders from excessive heat, mechanical shocks, physical damage, slag,  open flames,

 

  sparks, and arcs.
   •   Insure cylinders are held secure and upright to prevent tipping or falling over. 
•  Never allow the plasma nozzle or earth clamp to touch the gas cylinder, do not drape welding cables 
  over the cylinder.
   •  Never plasma cut on a pressurised gas cylinder, it will explode and kill you. 
   •  Open the cylinder valve slowly and turn your face away from the cylinder outlet valve and gas regulator.

Electronic magnetic fields.

 

The magnetic fields created by the high currents generated by 

plasma cutting may affect the operation of pacemakers and other vital electronic medical 

 

equipment.

•  Wearers of Pacemakers and other Implanted Medical Devices should keep away.
•  Implanted Medical Device wearers should consult their doctor and the device manufacturer before going 
  near any electric welding, cutting or heating operation.   
     

Noise can damage hearing. 

Noise from some processes or equipment can damage hearing.

This machine does not directly produce noise exceeding 80dB. The plasma cutting/welding 

procedure may produce noise levels beyond said limit; users must therefore implement all 

precautions required by law.  Wear approved ear protection if noise level is high.

Hot parts. 

Items being plasma cut generate and hold high heat and can cause severe burns.

 Do not touch hot parts with bare hands.   Allow a cooling period before working on the plasma 
torch. Use insulated welding gloves and clothing to handle hot parts and prevent burns.

Содержание Razor Cut80





















Отзывы: