background image

Using XPower Powerpack for the First Time

11

Using XPower Powerpack for the First Time

Recharging with the AC Charger

Recharging with the AC charger is a true “plug-in-and-
forget” charging method. We recommend leaving the AC 
charger connected when the XPower Powerpack is not in use.

To recharge with the AC charger:

1. Disconnect any 12 V DC appliances from the DC power 

outlets.

2. Disconnect any AC products from the XPower 

Powerpack and turn the AC Power 

ON

/

OFF

 switch to 

OFF

.

3. Insert the AC charger cable end into the AC charger input 

socket located under the red jump-starting clamp (see 
figure on page 6).

4. Plug the AC charger into a standard AC wall outlet.

The Battery Status LED changes from red to green when 
charging is complete (about 24 hours if the battery is 
completely discharged).

Important:

Prior to operating your AC appliance or 12 V DC 

appliance, ensure that the battery of the XPower Powerpack is 
fully charged. If the battery has been fully discharged, recharging 
with the AC charger may take up to 24 hours.

Note

:

The XPower Powerpack battery level LEDs are only 

accurate when the XPower Powerpack has been disconnected 
from all appliances and all charging sources for fifteen minutes.

CAUTION

Do not operate AC or DC appliances with the XPower Powerpack 
while the XPower Powerpack is being recharged with the AC 
charger.
The AC charger may be permanently damaged if AC appliances or 
12 V DC appliances are operated while the AC charger is 
connected.

XPower_PP_300_PlusEP.book  Page 11  Friday, May 19, 2006  11:29 AM

Содержание XPower Powerpack 300





























































Отзывы: