background image

975-0697-01-01

57

This guide for use by qualified installers only.

Battery Information

Battery Bank Sizing

Battery capacity 

Battery size or capacity is just as 

important as the battery type selected for use with the 
Freedom SW 230V. The batteries are the most important part 
of your system, so It is recommended that you purchase as 
much battery capacity as possible. A large battery will extend 
running time and ensure that your inverter/charger delivers 
full rated surge. 

It is recommended a minimum battery size of 200 amp-
hours (Ah) for moderate loads (< 1000 watts) and greater 
than 400 Ah for heavy loads.

See “Estimating Battery Requirements” for information on a 
more detailed calculation.

About Amp-hours 

A number of different standards are 

used to rate battery energy storage capacity. Automotive and 
marine starting batteries are normally rated in cranking amps. 
This is not a relevant rating for continuous loads like an 
inverter. Deep-cycle batteries use a more suitable rating 
system such as amp-hours (Ah). 

Amp-hour capacity is the number of amps a battery can 
continuously deliver during a specified number of hours. It is 
represented by the product of the two —amps multiplied by 
hours.
A typical single marine or RV battery rated for 100 Ah can 
deliver 5 amps @12 volts for 20 hours (5 amps × 20 hours = 
100 Ah @12 volts). This same battery can deliver a higher or 
lower current for less or more time, limited approximately by 
the 100 Ah figure (50 amps for 2 hours or 200 amps for a half 
hour), but usually the capacity figure given is only accurate 
for the specified duration (20 hours).
For Freedom SW 230V inverter systems requiring a 24-volt 
battery bank,

a pair of 200 Ah@12 volts batteries may be 
connected in series to create a 24-volt bank of 
200 Ah@24 volts capacity,

while two of these series pair branches may be 
connected in parallel to create a higher capacity 
400 Ah@24 volts battery bank.

FSW 230V Installation Guide.book  Page 57  Tuesday, August 7, 2018  9:18 AM

Содержание Freedom SW 230V























































































Отзывы: