Xantrex Freedom SW 230V Скачать руководство пользователя страница 35 | Manualshive

Страница: 35 / 86

Xantrex Freedom SW 230V Скачать руководство пользователя страница 35

975-0697-01-01

21

Installing the Inverter/Charger

This guide for use by qualified installers only.

Step 2: Mounting the Inverter/Charger

Considerations

Before mounting the Freedom SW 230V, take the following
two factors into account.
1. The weight of the inverter/charger requires two people to

install it.

2. Mounting considerations are shown in Figure 5 on page

The Freedom SW 230V dimensions and location of the
mounting holes are provided in Figure 5 on page 22.
Mount your inverter/charger before you connect any wires or
cables.

To mount the inverter/charger:

1. Remove the inverter/charger from its shipping container.
2. Verify that all components are present

.

3. Select an appropriate mounting location and orientation. To

meet regulatory requirements, the Freedom SW 230V must
be mounted in one of the orientations shown in Figure 5 on
page 22.

4. Mark the position of the mounting holes.
5. Pilot drill the six mounting holes.
6. Fasten the inverter/charger to the mounting surface with

six M6 steel screws or bolts.

HEAVY ITEM

The Freedom SW 230V Inverter/Charger is heavy (see “Inverter/Charger
Physical Specifications” on page 56)

.

The unit is too heavy for one person

to install safely. It is recommended that two people lift and mount the unit.
Always use proper lifting techniques during installation to prevent personal
injury.

Failure to follow these instructions can result in minor or moderate injury.

FSW 230V Installation Guide.book Page 21 Tuesday, August 7, 2018 9:18 AM

«
...
33
34
35
36
37
...
»

Содержание Freedom SW 230V























































































Отзывы:

Нет отзывов