Xantrex Freedom 458 10 Скачать руководство пользователя | Manualshive

Страница: 30 / 50

background image

30

NOTE: For low power system shutdown
mode, both the INVERT and CHARGE LEDs
must be OFF.

•

Testing for backfeed. If a backfeed

condition is indicated, disconnect from
shorepower and disconnect the AC output
wires on the inverter. Make sure the inverter is
OFF. Apply shorepower and measure for
voltage between the black and white wires that
were attached to the inverter output feeding the
electrical panel or loads, not the inverter output
wires. If there is voltage on these wires, a
backfeed condition exists and must be
corrected or damage will result.

3. Test the battery charger function:

•

With shorepower applied and the

transfer switch engaged, the battery charger
should be in operation. The CHARGE LED will
blink for 8 seconds. After the 8 seconds, the
unit will enter the charge mode and the LED
will be illuminated. (NOTE: When using
Temperature Sensitive Charging, this time may
be longer.)

NOTE: When AC is available, the unit will
automatically default to charge mode without
the operator setting the unit in CHARGE mode.
It is necessary to press the CHARGE switch
OFF, if you do not want to charge.

Verify the charger is working by using a

voltmeter. The battery voltage should gradually
increase. If using a Freedom Remote Control
Panel, the DC Amps LED indicates the current
the charger is putting out and the DC Volts
LED indicates an increase in battery voltage.

INSTALLATION

•

Turn the INVERT ON, the green LED

should blink. Remove shorepower and the
inverter should automatically pick up the AC
load when shorepower is removed.

Repeat the test for transfer and battery

charger with the generator if you have one.

Congratulations, you have completed a

successful installation.

«
...
28
29
30
31
32
...
»

Содержание Freedom 458 10



















































Отзывы:

Нет отзывов

Похожие инструкции для Freedom 458 10

Бренд: Hama Страницы: 12

Бренд: Lab599 Страницы: 12

Бренд: Latronics Страницы: 8

Бренд: qubev Страницы: 16

Бренд: GP Страницы: 4

Бренд: Elettro CF Страницы: 20

JG-4IFR12.8-150-Y

Бренд: ENERpower Страницы: 10

Бренд: Yuasa Страницы: 44

Home FlexCharfePoint

Бренд: ChargePoint Страницы: 20

SOLIDGRIP PRO NST-16EU

Бренд: Pingi Страницы: 8

Бренд: Tenergy Страницы: 4

Бренд: YATO Страницы: 40

Бренд: Jackson Racing Страницы: 14

KISAE ABSO Series

Бренд: Merlin Страницы: 8

Бренд: Listen Страницы: 2

Бренд: Seak Страницы: 3

IntelliCHARGER Li1208

Бренд: XS Power Batteries Страницы: 4

Бренд: V-TAC Страницы: 25

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды