Xantrex Freedom 458 10 страница 16 Скачать руководство пользователя | Manualshive

Страница: 16 / 50

background image

16

BATTERY CHARGING

NOTE: Freedom battery chargers are ON
whenever AC power is connected to the
charger input. The charger can be turned OFF
using the CHARGE switch on the front of the
unit. This sequence will occur each time
external AC power is available. The charger
can be turned ON/OFF using the Remote
Control Panel or Link Instrumentation.

Each time the battery charger is engaged,

the three-stage charger proceeds automati-
cally, resulting in an efficient complete charge
and safe battery maintenance. Use of the
Remote Control Panel or Link Instrument
provides the ability to periodically apply an
equalizing charge.

Refer to the Remote Control Panel or the

Link Instrument Owner’s Manual for more
information.

The battery charger stages are:

Stage 1 -

Bulk Charge

During the bulk

charge stage most of the energy that has
been consumed during discharge is returned
to the battery bank. This phase is engaged as
soon as the battery charger is activated. Full
rated charger current is delivered to the
battery bank until the acceptance charge
voltage limit is reached. This results in a relatively
rapid recharge.

Generally, a wet cell battery bank should

not be charged at a rate that exceeds 25% of
its capacity.

«
...
14
15
16
17
18
...
»

Содержание Freedom 458 10



















































Отзывы:

Нет отзывов

Похожие инструкции для Freedom 458 10

Бренд: Schumacher Страницы: 36

Бренд: Streetwize Страницы: 8

Бренд: PulseTec Страницы: 24

LocknCharge iQ Traveller 20

Бренд: IWS Страницы: 8

Бренд: UltraPower Страницы: 32

Бренд: ANSMANN Страницы: 42

Бренд: GP Страницы: 32

Бренд: MOB Страницы: 8

Бренд: Orbegozo Страницы: 7

Бренд: Hitachi Страницы: 44

Бренд: Sanyo Страницы: 1

Бренд: Sanyo Страницы: 16

V-PM1000 Series

Бренд: Veesta World Страницы: 46

Бренд: BlackVue Страницы: 4

COMPACT C 1600-12

Бренд: Studer Страницы: 23

Бренд: Alpha tools Страницы: 112

Бренд: Tronic Страницы: 10

Бренд: Victron energy Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды