Xantrex Freedom 458 10 страница 2 Скачать руководство пользователя | Manualshive

Страница: 2 / 50

background image

2

SAFETY SUMMARY

Safety information for installation and
operation is contained throughout this
manual where it applies and is not included
in this summary.

Definitions:

Warning statements

identify conditions or

practices which could result in personal injury,
loss of life, damage to equipment or other
property.

Fuse Replacement

For continued protection

against the possibility of fire, replace the fuse
only with a fuse of the specified voltage,
current and type ratings.

Power Source

To avoid damage, operate the

equipment only within the specified AC (line)
and DC (battery) voltages.

Servicing

To reduce the risk of electric shock

do not open this unit. There are no user
serviceable parts inside. Refer all service to
qualified personnel.

Thank you for purchasing a Xantrex Freedom 458 Series Inverter/Charger. Xantrex

Technology Inc. takes pride in manufacturing quality products specifically
designed to meet your power requirements.

Freedom 458 Inverter/Chargers provide silent, efficient and reliable AC power for a

variety of applications. They feature “hands-free” operation, automatic three-stage battery
charging and automatic AC transfer switching. For your convenience, service is available
world-wide from qualified service centers.

If you have any questions about your Freedom Inverter/Charger, please contact

Xantrex at

1-800-670-0707 (toll free) or 1-604-422-2777 (direct)

.

For technical support and additional information about Xantrex products, visit our Web

site at

www.xantrex.com

or e-mail us at

[email protected]

Notice of Copyright

Xantrex Freedom 458 Series Inverter/Charger

© December 2002 Xantrex International. All rights reserved.

Xantrex is a registered trademark of Xantrex International.

Disclaimer

UNLESS SPECIFICALLY AGREED TO IN WRITING, XANTREX TECHNOLOGY INC. (“XANTREX”)

(a)

MAKES NO WARRANTY AS TO THE ACCURACY, SUFFICIENCY OR SUITABILITY OF ANY TECHNICAL OR OTHER

INFORMATION PROVIDED IN ITS MANUALS OR OTHER DOCUMENTATION.

(b)

ASSUMES NO RESPONSIBILITY OR LIABILITY FOR LOSS OR DAMAGE, WHETHER DIRECT, INDIRECT,

CONSEQUENTIAL OR INCIDENTAL, WHICH MIGHT ARISE OUT OF THE USE OF SUCH INFORMATION. THE USE OF ANY
SUCH INFORMATION WILL BE ENTIRELY AT THE USER’S RISK.

Date and Revision

December 2002, Revision 2

Part Number

445-0193-01-01

Contact Information

Web: www.xantrex.com Email: [email protected]

Phone: 1-800-670-0707 (toll free in North America), 1-604-422-2777 (direct) Fax: 1-604-420-2145

«
1
2
3
4
...
»

Содержание Freedom 458 10



















































Отзывы:

Нет отзывов

Похожие инструкции для Freedom 458 10

Бренд: VDC Electronics Страницы: 7

Бренд: Skil Страницы: 44

e355 Gang Charger

Бренд: VeriFone Страницы: 2

Бренд: ShopBot Страницы: 22

Бренд: Thunder Страницы: 16

Бренд: Zendure Страницы: 83

Selectiva 4.0 2040

Бренд: Fronius Страницы: 68

Бренд: GP Страницы: 32

Бренд: Kobalt Страницы: 16

Бренд: Kobalt Страницы: 48

Бренд: Garner Страницы: 6

Бренд: Manhattan Страницы: 2

Бренд: Modtech Страницы: 4

Бренд: TCE Страницы: 9

Бренд: Sana Страницы: 17

Бренд: APLIC Страницы: 8

Бренд: APLIC Страницы: 32

Бренд: Currier Tech Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды