Xaar XJ128 Series Скачать руководство пользователя страница 20

Страница: 20 / 70

XJ128 and XJ128 Plus Printhead

XJ128 Guide to Operation



Xaar Document no: D031010302 Version A

Page 19

The operational temperature of the printhead will be controlled by several factors:



Thermal paths arising from the way the printhead is mounted (heat sinking)



Thermal paths in the application (mechanical and liquid)



The type of ink used



Internal heat generation (electronics etc)



Environmental heat dissipation

The maximum heat dissipation to be removed from the XJ128 printhead is 6 Watts. A typical value

for heat dissipation to be removed from the XJ128 printhead is 1 to 2 Watts, in normal operation.

The most effective way of removing heat from the printhead is through the thermally

conductive aluminium chassis. This should be used to

‘

cool

’

the printheads during

operation by removing heat generated by the printheads through a mechanical interface

with a heat sink.

4.4 Ink connection

Ensure that clean ink connectors are used. Ink connections to the printhead should be

prompt to reduce risk of contamination. Only use approved inks and associated

cleaning solutions available from Xaar.

Figure 4.6

–

XJ128 ink inlet

The ink connection to the printhead is through the ink inlet port as shown in figure 4.6. Push a 3.0mm

ID tube over the ink inlet port. A flexible-type of tubing should be used, as an interference fit is

required. The ink inlet port has an OD of 3.1mm. This is also shown on the mechanical drawing in

Appendix D. A 4mm OD/3mm ID tubing is recommended when supplying ink to the XJ128 printhead.

Ink inlet

Содержание XJ128 Series







































































Результаты поиска

Содержание XJ128 Series

Отзывы:

Похожие инструкции для XJ128 Series

Бренды по названию

Популярные бренды

Xaar XJ128 Series, Руководство по эксплуатации

Результаты поиска

Содержание XJ128 Series

Отзывы:

Похожие инструкции для XJ128 Series

Бренды по названию

Популярные бренды