X-Rite EasyTrax Скачать руководство пользователя страница 15 | Manualshive

Страница: 15 / 28

X-Rite EasyTrax Скачать руководство пользователя страница 15

EasyTrax Setup and Operation

13

5.

Adjust the location of the laser line by turning the adjustment screws clockwise or
counterclockwise. Adjust the screws until the laser line is centered down the length of the
color bar. Refer to the illustrations that follow to find the correct adjustment procedure for
your laser.

6.

When finished with alignment, press the laser button to turn off the laser.

•

Laser line is above the color bar

Turn both adjustment screws in the counterclockwise direction to move the laser line
down onto the color bar.

•

Laser line is below the color bar

Turn both adjustment screws in the clockwise direction to move the laser line up onto
the color bar.

•

Near side of the laser line is above the color bar

Turn the front adjustment screw in the counterclockwise direction to move the near
side of the laser line down onto the color bar.

Front screw

location

Back screw
location

Front screw

Back screw

Laser line

Laser line

«
...
13
14
15
16
17
...
»

Содержание EasyTrax





























Отзывы:

Нет отзывов